Question about Chevrolet Tahoe

1 Answer

2000 chevy tahoe 8 cly can you sent me a diagram or picture of this 8 cly. something to follow when i start pulling bolts nuts wires coil. i am going to fix this p0301 missfire problem.i am hoping it will be just a spark plugs. wish me luck

Posted by on

  • Rudy Cordova
    Rudy Cordova Aug 31, 2010

    thank you very much

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,796 Answers

HI!!

I'LL DO BETTER THAN THAT, CLICK ON THE LINK FOR A COMPLETE VEHICLE REPAIR GUIDE FOR YOUR 2000 CHEVY TAHOE

http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideMain.jsp

GOOD LUCK!! DON'T FORGET TO RATE THIS POST!!

Posted on Aug 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a coil pack on a Chevy Tahoe


To Remove......
1. Remove the spark plug wire from the ignition coil.
2. Disconnect the ignition coil electrical connector.
3. Remove ignition coil bolts.
4. Remove ignition coil.

To Install.....
1. Install ignition coil.
2. Install ignition coil bolts.
3. Tighten ignition coil bolts to 8 Nm the same as 71 inch pounds.
4. Connect ignition coil electrical connector.
5. And finally, install spark plug wire to ignition coil.

Apr 22, 2015 | Chevrolet Tahoe Cars & Trucks

1 Answer

Spark plug wiring diagram for 05 tahoe


Greg Bernett 2821 Solutions February 14, 2010
You didn't post your engine size so please pick the applicable diagram:


37926a4.gif
1996-98 4.3L Engines Firing Order: 1-6-5-4-3-2Distributor Rotation: Clockwise


8c292b0.gif
1996-98 5.0L, 5.7L and 7.4L Engines Firing Order: 1-8-4-3-6-5-7-2Distributor Rotation: Clockwise



30ced3d.gif
4.3L Engines Firing order: 1-6-5-4-3-2 Distributor rotation: Clockwise


de67664.gif
4.8L, 5.3L and 6.0L Engines Firing order: 1-8-7-2-6-5-4-3 Distributorless ignition system (one coil on each cylinder)


bf80c63.gif
5.0L, 5.7L and 7.4L Engines Firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise

Source: spark plug wiring diagram for 98 tahoe

  • avatar15.jpg
    ledsled378 2926 Solutions July 24, 2010

ebe6e34.jpg
01f93b7.jpg ..............................

Source: Need diagram for spark plug wiring for 1997 Chevy

Testimonial: "Thank you for your prompt response. Saved my husband from some distress!"
Was this solution helpful? Yes No

  • avatar1.jpg
    Dennis Weid. 44272 Solutions September 16, 2008

This was all I could come with, hope it helps.



ebead53.gif

Feb 27, 2013 | 1998 Chevrolet Tahoe

2 Answers

I have a 97 Chevy Tahoe 4x4 350 vortech, what wrench size do u use to take off my fuel filter ,that is the line going in.?


it just a basic tools. find the filter and see what size it is.
crawl under the truck on the driver's side, follow the fuel line from the fuel tank to the filter(shape:cylindrical).
make sure the line has no pressure. you should pull the fuse for the "fuel pump" relay, then start the engine and allow it to stall.

Mar 02, 2012 | 1997 Chevrolet Tahoe

3 Answers

Change order for 5.7 liter chevy tahoe spark plugs


You can replace them in any order, but the Firing Order is 1,8,4,3,6,5,7,2

Aug 30, 2010 | Chevrolet Tahoe Cars & Trucks

1 Answer

The starter is out on my 97 Tahoe LT


On starter, mark the wires before removing. There should be two wires on the starter. One for the ignition which is by itself, one for power and one for the solenoid to attach to. You don't need to disconnect the solenoid wire. Just the ignition wire and the red power wire. The ignition wire just pulls off. But pull carefully so the end don't break. The red power wire has a nut on it to remove.
Then remove the two starter bolts and pull it out.

Jul 26, 2010 | 1996 Chevrolet Tahoe

1 Answer

1988 Chevy Tahoe Starter going out. Need to replace


Generally starters have 2 or 3 bolts and a thick wire coming from the battery and other miscellaneous connections.

You did not specify a vehicle that was on my list, i.e. 1988 Chevy Tahoe.

However, it may be similar to a Suburban R10:
REMOVAL & INSTALLATION The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
  1. Disconnect the negative battery cable at the battery.
  2. Raise and support the vehicle.
  3. Disconnect and tag all wires at the solenoid terminal. NOTE: Reinstall all nuts as soon as they are removed, since the thread sizes are different.
  4. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter. Fig. 1: Starter mounting location — 4.8L engines 84903021.gif
    Fig. 2: Starter mounting location — 4.3L and 5.0L engines 84903022.gif
    Fig. 3: Starter mounts — 5.7L and 7.4L engines 84903023.gif

  5. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck. To install:
  6. Position the starter and tighten all bolts as follows: R/V Series:
    • Thru-bolts: 40 ft. lbs. (54 Nm)
    • Bracket bolt: 30 ft. lbs. (41 Nm)
    • Nut (gas): 11 ft. lbs. (15 Nm)
    • Nut (diesel): 90 inch lbs. (10 Nm)
    C/K Series:
    • Thru-bolts: 35 ft. lbs. (45 Nm)
    • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
    • Nut (diesel): 75 inch lbs. (8.5 Nm)
  7. Reconnect all wires. Fig. 4: Disconnect the negative battery cable 87982p25.jpg
    Fig. 5: Remove the starter retaining bolts 87982p30.jpg
    Fig. 6: Remove the starter from the vehicle 87982p31.jpg
prev.gif next.gif

Jul 19, 2010 | 1984 Chevrolet Chevy

2 Answers

2000 CHEVY TAHOE THE FUEL PUMP bit the bullet so


Take your vin number to any Chevy Dealer's Parts Counter. They can pull up the parts diagram and give you a part number. The ring is most likely a dealer part. So you will need to go to the dealer anyway to buy this part.

Jan 25, 2010 | 2000 Chevrolet Tahoe

2 Answers

Replacing spark plugs in a 2002 chevy tahoe


EACH ONE OF THE SPARK PLUGS IS LOCATED UNDER INDIVIDUAL COILS. YOU MUST FIRST REMOVE THE BOLT ON TOP OF THE COIL AND GENTLY TWIST AND PULL UP ON THE COIL WITHOUT RIPPING THE BOOT. UNPLUGGING THE ELECTRICAL CONNECTOR IS NECESSARY ON MOST MODELS. SOME OF THE NEWER MOTORS HAVE A COVER ON THE TOP OF THE ENGINE THAT HIDES THE COILS. PLEASE KEEP ME POSTED. THANKS FOR USING FIX-YA. BEST OF LUCK

Sep 02, 2009 | 2002 Chevrolet Tahoe

3 Answers

Coil pack. what and where is it? what does it look like?



 
 
Ignition Coil
Removal & Installation
4.2L Engine
1997-2000
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio ignition interference capacitor connector
The locking tabs
The six ignition wires, marking for reinstallation
The brackets
The spark plug wire set
CAUTION
Spark plug wires must be connected to the proper ignition coil terminal. Mark spark plug wire locations before removing them.
The accelerator cable bracket nut
The accelerator cable bracket bolt
The accelerator cable bracket and position it aside.
The two ignition coil nuts
The ignition coil stud bolt
The ignition coil
To Install:
Install or connect the following:
The ignition coil
The two ignition coil nuts
The ignition coil stud bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The accelerator cable bracket
The accelerator cable bracket nut
The accelerator cable bracket bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The ignition coil electrical connector
The radio capacitor connector


CAUTION
The Spark plug wires must be connected to the proper ignition coil terminal.
Squeeze the locking tabs and connect the six ignition cables.
2001-2003
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The spark plug wires, marking for reinstallation
CAUTION
The sparkplug wires must be connected to their correct ignition coil terminal.
The ignition coil
The bolts
Inspect the ignition coil for carbon tracks or damage.
To Install:
Inspect the ignition coil for carbon tracks or damage.
Install or connect the following:
The ignition coil
The bolts
Torque to: 53 inch-lbs (6 Nm)
The ignition coil electrical connector
The spark plug wires, in their original positions
4.6L Engine
1997-1999
To Remove:

NOTE: This procedure is for either RH or LH ignition coil.
Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires by squeezing the locking tabs (four each side)
CAUTION
The spark plug wires must be connected to their proper ignition coil terminal. Mark spark plug wire locations.
The bolts
The ignition coil
To Install:
NOTE: The procedure is for either LH or RH ignition coil
Install or connect the following:
The ignition coil
The bolts
Torque to: 44-62 inch-lbs (5-7 Nm)
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires (four each side), into their original positions by squeezing the tabs


CAUTION
The spark plug wires must be connected to their proper ignition coil terminal.

 
Top of Form 1
Bottom of Form 1

Mar 28, 2009 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...