Question about 1994 Chevrolet Silverado 2500

Open Question

How do you remove the evaporator core from a 1994 chevy silverado?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Shouldibuyit
  • 44 Answers

SOURCE: replace heater core 1994 chevy g20 conversion van

Here a are the instuctions to remove it. I did not know if you have A/C or not so I included both for you.

REMOVAL & INSTALLATION
Without Air Conditioning
ALL MODELS
See Figure 1

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery bottle.
  3. Place a pan under the van and disconnect the heater intake and outlet hoses. Quickly remove and plug the hoses and support them in an upright position. Drain the coolant from the heater core into the pan.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Remove the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw. Remove the duct.
  2. Remove the engine cover.
  3. Remove all the instrument panel attaching screws.
  4. Carefully lower the steering column. Raise and support the right side of the instrument panel. Refer to for further details.
  5. Remove the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  6. Disconnect the temperature door cable. Carefully fold the cable back and out of the way.
  7. Remove the three nuts from the engine compartment side of the distributor case and the screw from the passenger compartment side.
  8. Remove the heater case and core assembly.
  9. Remove the core retaining straps and remove the core.
To install:
  1. Install the core.
  2. Install the core retaining straps.
  3. Install the heater case and core assembly.
  4. Fasten the three nuts on the engine compartment side of the distributor case and the screw on the passenger compartment side.
  5. Connect the temperature door cable.
  6. Install the defroster duct-to-case attaching screws and the two screws attaching the distributor to the heater case.
  7. Install the steering column.
  8. Fasten all the instrument panel attaching screws.
  9. Install the engine cover.
  10. Install the duct. Install the heater distributor duct-to-case attaching screws and the duct-to-engine cover screw.
  11. Connect the heater intake and outlet hoses.
  12. Fill the cooling system.
  13. Install the coolant recovery bottle.
  14. Connect the negative battery cable.
1990-95 MODELS With A/C

  1. Disconnect the battery ground cable.
  2. Remove the engine cover.
  3. Remove the steering column-to-instrument panel bolts. Lower the column carefully.
  4. Remove the upper and lower instrument panel attaching screws. Remove the radio support bracket screw.
  5. Raise and support the right side of the instrument panel.
  6. Remove the lower right instrument panel bracket.
  7. Remove the vacuum actuator from the kick panel.
  8. Disconnect the temperature cable and vacuum hoses at the case. Remove the heater distributor duct from over the engine hump.
  9. Remove the two defroster duct-to-firewall attaching screws below the windshield.
  10. Under the hood, disconnect and plug the heater hoses at the firewall.
  11. Remove the three nuts and one screw (inside) holding the heater case to the firewall.
  12. Remove the case from the van. Remove the gasket for access to the screws holding the case together. Remove the temperature cable support bracket. Remove the screws and separate the case. Remove the heater core.
To install:
  1. Install the heater core.
  2. Assemble the case and fasten the screws.
  3. Install the temperature cable support bracket.
  4. Position the gasket, then install the case in the van.
  5. Fasten the three nuts and one screw (inside) holding the heater case to the firewall.
  6. Connect and plug the heater hoses at the firewall.
  7. Fasten the two defroster duct-to-firewall attaching screws below the windshield.
  8. Install the heater distributor duct.
  9. Connect the temperature cable and vacuum hoses at the case.
  10. Install the vacuum actuator at the kick panel.
  11. Install the lower right instrument panel bracket.
  12. Fasten the radio support bracket screw.
  13. Fasten the upper and lower instrument panel attaching screws.
  14. Fasten the steering column-to-instrument panel bolts.
  15. Install the engine cover.
  16. Connect the battery ground cable.
  17. Refill the cooling system as necessary.

Posted on Nov 28, 2008

fastboyz
  • 674 Answers

SOURCE: 1994 Chevy Silverado

d2f5142.gifi hope this is what you are looking for
good luck
paul

Posted on Nov 17, 2008

  • 3600 Answers

SOURCE: removing evaporator in 93 chevy pickup

Did you connect the lines? and did you break loose the tar that holds itto the car and seals the holes for the pipe? You maya have to remove the outter core cover to getto the last screws to get it out.

Posted on Jul 18, 2009

  • 289 Answers

SOURCE: How to replace a heater core in a 1994 chevy 1500

As with all vehicles it seems the first part that they build around is the heater core. It is under the dash above the floor housed in a black plastic sealed box. Sealed with goop. Locate that box and start removing everything around it that is peventing taking the cover off. Of course disconnect the heater hoses under the hood a thefirewall.

Warning it is never as easy as it sounds.

Posted on Nov 29, 2009

Jim1969pa3
  • 152 Answers

SOURCE: I have a 1999 chevy silverado and I need to change heater core

Not a whole lot different. Just need to keep removing plastic down at the heater until you get to the heater core. Then disconnect it on the firewall side.

Posted on Dec 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 mazda evaporator core


The evaporator core is inside the air ducting which is behind the dash assembly, the entire dash must be removed to replace the evaporator core.

Jul 16, 2012 | 1996 Mazda Protege

2 Answers

How do you replace the evaporator core for the a/c? on a 1994 gmc p/u truck, I've already have the dash out having promblems removing the duct work, what's next? or is there a maunal that will show me.


your instructions are on how to replace the condenser on a 1994 gmc sierra but the title says it is the directions for replacing an evaporator. please correct your title.

Aug 08, 2010 | 1994 GMC Sierra

2 Answers

Orfice tube location


the fixed orifice is located in the inlet tube to the evaporator core, this is where the small high pressure AC line from the compressor connects to the tube sticking out of the engine firewall, u will most likely need a special tool to remove it, here is a web link to the tool, don't damage the evaporator core by trying to remove the orifice tube without this if it is stuck down in the tube.

http://www.google.com/products?hl=en&q=ac+orifice+tube+removal+tool&rlz=1R2ADBF_en&um=1&ie=UTF-8&ei=X4BETJiZC4-esQPw-ajJDA&sa=X&oi=product_result_group&ct=image&resnum=3&ved=0CCsQzAMwAg

Jul 19, 2010 | 1995 Chevrolet Lumina Apv

2 Answers

How to replace a heater core in a 1994 chevy 1500


As with all vehicles it seems the first part that they build around is the heater core. It is under the dash above the floor housed in a black plastic sealed box. Sealed with goop. Locate that box and start removing everything around it that is peventing taking the cover off. Of course disconnect the heater hoses under the hood a thefirewall.

Warning it is never as easy as it sounds.

Nov 29, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

I have 1994 chevy 1500 i can't remove battery.


remove leads, take off battery hold down, might have to cut off replace with new hold down from auto parts store, clean leads or replace  

Sep 20, 2009 | 1994 Chevrolet Silverado 2500

1 Answer

I have a 1993 Chevy Silverado 2500 with a 5.7 liter 350. How do I bypass the heater core by connecting two hoses? Will the only negative impact be that I will not have a heater?


You can remove both hoses from the core and put them together using a short length of copper plumbing pipe. No problem to engine from this it flows through just like its going to core( engine can't tell the difference)

Jun 18, 2009 | 1994 Chevrolet Silverado 2500

1 Answer

I have a 2003 chevy silverado that is blowing hot air through the vents when the temp is set at its coldest setting


check under the dash to see if the blend door is operating, this ian internal door between the heater core and the a/c evaporator. also check that the drain hose from the evaporator make sure its clear and water is coming out of it,otherwise the evaporator will freeze solid and therefore no cold air

Apr 09, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

Removing the heater core from 2000 silverado


When I replaced the heater core on my 95 Suburban, I seem to remember having to disconnect the A/C lines on the firewall for the evaporator. There were also several nuts to remove on the engine firewall side from studs on the heater box that pass thru the firewall. It is definately a lot of work.

Good luck.

Jan 10, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

Heater core on silverado


You should have enough room to work by just removing the glove compartment door...

Dec 11, 2008 | 1994 Chevrolet K1500

3 Answers

Replace the Evaporator Core in a 1994 Saturn SC1


If you go to your local Auto Parts store (Advanced Auto, Auto Zone, Pepboys) get the Haynes Manual for your car it tell you step by step and has some pictures too........very helpful

Jul 04, 2008 | 1994 Saturn Sc

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...