Question about Suzuki SX4

2 Answers

2007-Maruti SX4 ABS and BRAKES lights comes on. My car was alright untill i gave it for service they there replaced the front right side wheel bolts as their thread were worn out now the abs and brakes lights have come on and its not working normal. please advice what to do now?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Contributor
  • 274 Answers

Are the brakes going to the floor or do they not feel right is fluid leaking out,is there plenty of brake fulid.I would take it back and have them fix it rigt or make a complaint with manager..Are the brake pads good?

Posted on Aug 29, 2010

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 20 Answers

This may happen it is very same problem you can get it done from your respect service center.
Maruti SX4 Review

Posted on Jul 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abslight stays on. How to fix? This is a2007trailblazer?


First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

Dec 30, 2016 | 2007 Chevrolet Trailblazer

Tip

All Cars ABS light on


For those of you that have abs brakes if the brake light comes on what happens Is it goes into standard brake mode. This means that the brakes lock up as if they had no abs system so if you jam the brake pedal down the wheels will stop spinning. If you are in wet weather or on ice it could cause a skid and cause you not to turn while slamming on the brakes. So if you have the ABS light on you need to have them checked but does not mean you have to take it to the shop right then it can be later, be aware that extended use without the ABS being serviced could cause damage to the ABS system. Most ABS lights are caused by a dirty magnetic ring on one wheel, on rear wheel drive cars it could be the one on the end of the transmission or the front of the differential. These put out 2.5 volts dc to test use Digital meter put it on 5 volts dc and spin the wheel with the connector disconnected probe the ring connector to see if yo have 2.5 volts if not it has a broken ring or wire, if the magnetic ring is broken it will have to be replaced. Most models have to have the rotor replaced on the front end and the sensor on the rear end.

on Dec 03, 2009 | Chevrolet 2500 Cars & Trucks

2 Answers

Fault code c 1044


Think I found the solution or a thread discussing your Fault Code at Jeep Forum (Jeep patriot abs,4wd,esp,Trac control lights on after replacing rear wheel bearing) Jeep patriot abs 4wd esp Trac control lights on after replacing rear wheel...

Jan 07, 2016 | 2007 Jeep Patriot Limited

1 Answer

What could be the problem when I aply brakes pedal gets real hard where car wont stop when braking coming to a stop brk. light and abs lights on


Hey Joes, 1 problem at a time ,if brake light is coming on that is in the proportion valve ,did you have to push reset button to make light go out,? if the ABS lite is coming on what you can do to check and see if that is the problem is unplug it and try brakes ,it will deactivate ABS and give you normal braking and ABS light will be on ,see if symptyms change , also did you reset ABS sensors to the tone wheel when you replaced rotors ? I don't know what you have and I have seen some cars need a importaint reset procedure for abs to work properly. good luck I hope I gave you some good things to look at that help you.
Woody

Oct 28, 2014 | Cars & Trucks

1 Answer

2006 suzuki sx4. the brake pedal pulses when applied during a left hand turn. it has new pads and also a new master cylinder. The system has been bled several times. it feels like the ABS system is trying...


warped rotor (s)
or wheel falling off (lugs loose) causing rotor walk , on the wild side.
do not delay fixing brakes.
remove wheel
spin hub , see it wobble.? bingo.
could be bad wheel bearings.
have a brake man inspect the brakes.
i have a tool to measure both bad bearings and rotor warp
its called a dial indicator. but you break guy can find this i about
30min or less. (old hat)

Feb 20, 2014 | 2006 Suzuki SX4

1 Answer

When applying brakes on 99 Ford Explorer they feel good until just berfore stopping then it feels like a push back on pedal and a bit of chatter like the ABS is coming on. Doesn't feel right. No Problem...


I had the same problem with my 2002 Silverado. The grease seal on the right front wheel bearing went up letting grease build up on sensor . Disconnect ABS sensor wire at wheel one wheel at a time. Abs light on dash will come on but that's ok. drive and stop easy with wire disconnected until brakes feel normal. Then you will know wheel is the problem.

Oct 27, 2013 | 1999 Ford Explorer

1 Answer

I replaced front brake pads on 2007 dodge grandcaravan brakes seem fine but ABS light is on


Each wheel has its own ABS sensor. Check to make sure that you haven't accidently disconnected the wire from 1 of the wheel hubs. If they are connected then you have to check and make sure the sensor is not damaged. If yoiu cannot see any obvoius damage then you need to test each wheel sensor to see which sensor is malfuntioning so you know which one to replace they are ezspensive so you do not want to just replace them untill you find the right one it is worth paying a garage to determind which wheel is the problem by testing each wheel.

Apr 29, 2011 | Dodge Grand Caravan Cars & Trucks

2 Answers

Replaced front brakes ABS light comes on and


Hi:
The ABS light on means an ABS malfunction. You should be able to have a auto parts store scan your car and find out what code is tripped, for free, but my guess is that one of your front wheel speed sensors is out of whack, or dirty or something.
When the light is on, your normal brakes work fine, but you have no ABS, so your car will take longer to stop in emergency situations.

Nov 06, 2009 | 1999 Volkswagen Passat

2 Answers

ABS signal light comes on


it means that you are having a malfunction with the abs system on your brakes....id have that checked immediately by a certified mechanic

Feb 11, 2009 | 2005 Chrysler Pacifica

1 Answer

ABS light, light come on goes off and comes back at 5-10mph


have had simmilar problemn with my 1992 licoln towncar do have a solution however will cost hundreds you have a ABS speed sensor out as u kno the problem is you cannot only replace one because they are wire through the axels you have to replace both meaning either both front or both rear in your case if front driversside is faulty you will need to replace both unhooking will only cause light to permantely stay on one suggestion that may help atleast to get an inspection would be to dissconnect sensors to that paticular wheel shut off engine and restart when light is off dissconnect batter for 5 mins then reconnect tghis will reset computer inside possibly giving you enough time to get an inspection befoere computer resets and abs comes back on however it is not guarented to work depends on severit y of damaged sensor and how quickly you module can reset note that this is a temo fix abd sensor will not prevent any stopping or cause danger to braking system it will infact stil engage possibly not on that wheel but that is the problem with an abs as apposed to just a standard anti lock braking system more sensor to break and cost hundreds

Feb 10, 2009 | 1992 Cadillac DeVille

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...