Question about 1994 Buick Regal Gran Sport

1 Answer

How do I remove the center console of a 1994 Buick Regal in order to repair the light gauge showing drive, reverse, neutral etc? (The plastic pieces on both the automatic shift lever and the indicator lights have fallen down into the console)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 5,763 Answers

You should be able to remove the trim plate that where the shifter is, it the cover and from there you will be able to replate the bulb for the selector window,

Posted on Aug 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Reverse lights stay on in drive 2004 buick rendezvous cxl


Backup Lamps
The TURN SIG fuse in the console fuse block supplies battery positive voltage to park neutral position switch. When the gear selector lever is in the REVERSE position, power is supplied to both of the backup lamps. The backup lamps are grounded at G401 and G402.
Do you know what DTC'S - diagnostic trouble codes are ?
DTC B2552
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamp relay control circuit energizing the backup lamp relay. The BCM connects directly to the center console fuse block with no external wiring between them.
DTC B2553
The body control module (BCM) controls the backup lamp relay. The BCM grounds the backup lamps relay control circuit energizing the backup lamp relay. The BCM connects directly to the center console fuse block with no external wiring between them.
Backup Lamps Always On
  1. Turn ON the ignition.
  2. Shift the gear selector lever to the REVERSE position and then to the PARK position.
Do the backup lamps turn on in REVERSE and turn off in PARK?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3

Remove the backup lamps relay.
Do the backup lamps turn OFF?
Go to Step 5
Go to Step 4

4

Repair a short in the backup lamps relay switched battery positive voltage supply circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you complete the repair?
Check the back-up lamps relay #45 in the center console fuse/relay box .
Fuse Block - Center Console
Inside of console, behind the right console access panel

Check

Jun 11, 2016 | 2004 Buick Rendezvous

1 Answer

How do you install a vacuum modulator in a 94 regal


Remove the vacuum line at the modulator. Remove the bolt and the modulator assembly retainer. Remove the modulator assembly. Reverse order to install.

NOTE: if the modulator valve comes out of the bore when removing the modulator vacuum assembly, note the orientation of the valve and reinstall it in the bore before installing the new vacuum modulator assembly. (see picture)


dttech_161.gif

Aug 13, 2011 | 1994 Buick Regal Gran Sport

2 Answers

Instrument lights failed, fuses seem ok, how do I reach the blub?


first, you need to unscrew a lot to remove your gauge box (the one that contains all instrument lights, speedometers, tachometers, fuel gauge, etc). then, after removing your gauge box, you can see at the back side the location of the bulbs.

Aug 05, 2011 | 2001 Buick Regal

1 Answer

Fuel gauge is acting erratic. How do you replace the fuel sending unit on a Buick regal 2000?


you must remove gas tank, take out sender then reinstall in reverse order..

Jan 13, 2011 | 2000 Buick Regal

2 Answers

How to replace neutral saftey switch on a 1980 cadillac deville?


Use like reference guide for GM Cadillac 1967-1989 Repair Guide Neutral Safety Switch - REMOVAL & INSTALLATION

All Except 1985-89 Eldorado and Seville
See Figure 1
The neutral safety switch prevents the engine from being started in any transmission position except Neutral or Park. The switch is located on the upper side of the steering column under the instrument panel on column shift cars, and inside the shift console on floor shift models.
  1. Remove the console for access on floor shift models.
  2. Disconnect the electrical connectors.
  3. Remove the neutral switch.

To install:
  1. Place 1967-70 column shift lever models in Drive, and 1971 and later models in neutral. Locate the lever tang against the transmission selector plate on column shift models.
  2. Align the slot in the contact support with the hole in the switch. Insert a 3 / 32 in. (2.38mm) diameter pin in place. The switch is now aligned in Drive position.

1973 and later neutral safety switches have a shear-pin installed to aid in proper switch alignment so that insertion of a pin is unnecessary. Moving the shift lever from Neutral shears the pin.
  1. Place the contact support drive slot over the drive tang. Install the switch mounting screws.
  2. Remove the aligning pin. Connect the electrical wiring, and replace the console.
  3. Set the parking brake and hold your foot on the service brake pedal. Check to see that the engine will start only in Park or Neutral.
7b3f2a9.jpg

Fig. 1: Installation of a common neutral safety switch



ADJUSTMENT
See Figure 2
1974 and later cars do not have a neutral safety switch. Instead, these cars have an interlock between the lock and the transmission selector, which is non-adjustable.
  1. Place the shift lever in Neutral.
  2. Move the switch until you can insert a gauge pin, 3 / 32 in. (2.38mm) diameter, into the hole in the switch and through to the alignment hole.
  3. Loosen the switch securing screws. Remove the console first, if necessary.
  4. Tighten the screws and remove the pin.
  5. Step on the brake pedal and check to see that the engine will only start in Neutral or Park.
05843d3.jpg


Fig. 2: Adjustment of a common neutral safety switch


1985-89 Eldorado and Seville
See Figure 3

All neutral safety/back-up light switches come with a small plastic alignment pin installed. Leave this pin in place.
  1. Place the shifter assembly in the Neutral position.
  2. Remove the shifter lever-to-switch nut and the lever.
  3. Disconnect the electrical connector from the neutral safety/back-up light switch.
  4. Remove the neutral safety/back-up light switch-to-transaxle bolts and the switch from the vehicle.

To install:
  1. Position the shifter shaft in the Neutral position.

If using an old switch or the plastic pin (new switch) is broken, install a3/32in. (2.38mm) diameter pin gauge (drill bit) into the neutral safety/back-up light switch; the switch is then locked into its Neutral position.
  1. Align the flats of the shifter shaft and the neutral safety/back-up light, then, align the switch-to-tang on the transaxle. Torque the switch-to-transaxle bolts to 22 ft. lbs. (30 Nm). Remove the pin gauge.
  2. To complete installation, reverse the removal procedures. Make sure that the engine starts only in the Park and Neutral positions.
c796664.jpg

Fig. 3: Neutral start and back-up lamp switch - 1985-89 Eldorado and Seville

Hope help with this (remember rated and comment this). Good luck.

Mar 21, 2010 | 1980 Cadillac Deville

1 Answer

Buick Regal cup holder problem


Yes absolutely you can my friend. and you are correct this will fit 1997 to 2004 actually!

Jul 10, 2009 | 1996 Buick Regal Olympic Gold

1 Answer

1999 Buick Regal Tail lights, how to get to them.


Hello;
On the Buick, your tail light lens are smooth with no screws accessable from the outside. So, open the trunk and you will see either cardboard or carpeted panels surroounding the trunk. Pull these away and you will see some plastic wingnuts (3-4 each side). Remove the wingnuts, and then pull the light towards the rear from the outside. Your wires and sockets will thrn be accessible. Usually depress the lock and give the socket a 1/4 turn and pull out. Replace the bulb, reinstall in the reverse order.
Hope this helps you.
Thanks;
Rich
RPM Northwest

Jan 22, 2009 | 1999 Buick Regal

Not finding what you are looking for?
1994 Buick Regal Gran Sport Logo

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...