Question about Chevrolet Camaro

1 Answer

Have a muncie 21 in a 1968 camaro with a 396. When i shift from first gear to second at about 20 mph, the rpms spike, feels like 2nd gear is lower than first gear. I can also take off from a stop in any gear, 1-4. Reverse works fine, i adjusted the linkage arms mysleft. Visually laying under car, and having some one shift, it hits all the gears properly. Whats the problem?!?! THanks MIke

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 4,336 Answers

Mike, this description sounds like the lever is reversed for 1st and 2nd..

Posted on Aug 29, 2010

  • mjstempky Aug 29, 2010

    It does, but, why can i take off from a stop in any gear.... and is it really possible to reverse first and second gear lever.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1997 Jimmy runs fine in idle when I take off the vechile is fine until it reaches 20 mph it won't accelerate and the rpms increase up to 3000 but no speed. What's wrong it's a 4 wheel d


Sounds like 2nd gear in the transmission is slipping. Cars usually shift at 15-20 mph from first to 2nd. First check the trans fluid.

Mar 17, 2013 | 1997 GMC Jimmy

1 Answer

1993 gmc suburban rpms jump without acceleration, hard shift from 1st to 2nd


Sounds like a vacuum leak probably at the modulator valve on or close to the transmission.

Feb 06, 2013 | 1993 GMC Suburban

1 Answer

2002 silverado 1500 HD Transmission skips second gear


have the fault codes read to find out the servo/solenoid that is not working'
check that the vacuum actuator for the transmission is working and that the vacuum hose is connected
that is the unit that makes ratio changes possible at certain rpms and vacuum settings from accelerator pedal positions

Apr 21, 2017 | 2002 Chevrolet Silverado 1500HD

1 Answer

Clutch starting to slip 1994 camaro can i adjust it


It does sound like your clutch needs replacing. Adjusting the clutch may help but will not solve the problem. If the transmission has not been serviced for a long time it is a good idea to replace the transmission fluid, inspect the pressure plate. They may also start to wear.

Feb 05, 2012 | 1994 Chevrolet Camaro

1 Answer

I installed a muncie m20 tranny in my 72 camaro and thought the shft rods were set ..but turns out 1st gear was in the 2nd gear position i tried flipping rod paddles upside down now gears are locked up...


You are right about the shift pattern. Reverse is hard left and up.If your gears are locked up, you'll probably have to remove the side cover and reset the shift levers to their neutral position and then slide gears around to put it back on. With it back on the shift levers should point up toward the car floor. 3-4 is the shift lever closest to the engine. 1-2 is the middle one and reverse is the one closest to the back of the tranny. Check all your swivel points for looseness. If there is any play then you'll have to bush it out or you'll have trouble getting it to shift into gear and stay in. I used some old copper pipe to make bushings on mine, because it used to jump out of gear.
To properly attach your shift linkage, put the shifter and the trans mounted shift levers in neutral. Loosen the locking clamps so the shift rods slide freely. start with the reverse lever, which is the inner most rod on the shifter and tighten the rod nut against the swivel. Then tighten the lock nut. Do the same with the 1-2 rod on the middle rod on the shifter and then the 3-4 which is the outside rod . This should set you up, according to Chilton.
They note that if the tranny is 68 Camero Muncie the shift rods need to be shortened 3 complete turns of the lock nut.
Hope some of this helps.

Aug 13, 2010 | Chevrolet Camaro Cars & Trucks

2 Answers

ABS system works fine after 76 mph is reached. Until then when I apply the brakes it acts as though Im sliding on ice. I can feel it fighting to stop in my peddle. Also it does not want to shift out of...


this sounds like the cpu in the car playing up (the cars computer brain) have it chequed out at the shop to find out if any codes are showing up

Oct 30, 2009 | 1995 Ford Contour

2 Answers

I have a 94 gmc sierra with 350 that has problem shifting to 2nd


Your problem likely resides with the hydraulic valve that operates the band for second gear, or lack of hydraulic pressure in the transmission. If the actuator in the transmission that operates second gear is getting sticky, then it will cause this. A filter change and flush may help, but it's likely time to start looking for someone to tear down your transmission, or replace it.

Oct 20, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...