Question about 2000 Mazda MPV

1 Answer

How does the altenator come out after it is unbolted?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

If it is like the ford probe mounted on the passenger side you will have to remove the trans-axle. It has four bolts. you will need to jack the car up and put it on stands. remove tire and remove trans-axle. Hope this helped tim

Posted on Aug 29, 2010

Testimonial: "Looks like your right, guess I'll be removing the axle this sunny Sunday. You have a great day?"


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to change alternator on 2008 nissian altima

For a V6 altima easiest way is to remove the radiator. Altenator is on the front of the engine at the bottom. With the radiator out of the way can fit it out. Ususal atuff for the altenator. Disconnect the battery. Loosen the belt to remove it. The unplug connector and the 12mm bolt for the output. Then unbolt altenator to remove. Will not be able to fit it out without removing radiator

Mar 04, 2017 | Cars & Trucks

1 Answer

Replacing belt tensioner

Unbolt it !

Really -watch some You Tube Video

Jul 17, 2014 | 1993 GMC Sierra

1 Answer

How do i take off a alternator for a mitsubishi Pajero, 1992

IF it is the same as my 89 Montero (which it should be) you would first disconnect the ground for the battery (safety first), loosen the belt tensioner enough to remove the altenator drive belt and then unbolt the alternator. Keep the bolts placed in a manner in which you can be sure which one goes where. I believe the bottom bolt is going to give you the most trouble. It may have to come out from the back. It's been over a year since I pulled mine so I can't remember for sure. HTH

Oct 14, 2013 | 1995 Mitsubishi Montero

1 Answer

Cannot get altenator out of motor bay.Altenator is unbolted and free from bracket.

Make sure that the wires are removed, belt is removed, and the top and bottom bolts are completely out of the holes. If all of that is done the alternator is just jammed in the recepticle. Take a large screwdriver or small/ medium prybar and place between the alternator and brackets and pull. it may be tough but it will come out. Good luck and i hope i was of some assistance. Please leave feedback if i was able to help.

Thank you for your question!

Mar 30, 2011 | Kia Optima Cars & Trucks

1 Answer


when you unbolt the alternator it will slide and loosen the tension. Good Luck Tim

Mar 25, 2011 | Ford Ranger Cars & Trucks

1 Answer

How to change an altenator on a 2005 dodge strstus

The best advise I can give you is go to Auto Zone or your local Auto parts store and purchase the Haynes Repair manual on your vehicle. 1. Disconnect the battery. 2. remove the Drive Belt. 3. Disconnect the the cables from the Alternator. 4 . Unbolt the alternator. Reverse the process to install the new unit.

Jul 17, 2010 | 2005 Dodge Stratus

1 Answer

Replacing a altenator

Disconnect the battery, unbolt the alternator, remove the wires and write down or draw yourself a picture so you can put them back where you got them. Some need to be twisted and turned a bit to get them out. Replacing is the reverse of removal. It sometimes helps to partially un-bolt the brackets from the engine so you have a bit of room to get it back in.
My rule: If it's in your way, remove it (that can often save hours of extra work)

May 22, 2010 | 1991 Jeep Wrangler

2 Answers

How to remove the altenator in a 1997 Deville

disconnect the positive lead to the battery and disconnect the wires behind the alternator loosen all 3 bolts / nuts and brackets and remove replace in reverse method

Sep 23, 2009 | 1997 Cadillac DeVille

2 Answers

How do you install altenator

Disconnect the battery first and formost.
Then disconnect the electrical plug on the old alternator.
Take off the serpentine belt.
Unbolt the old alternator off the engine.
Bolt new Alternator on engine
Re-install serpentine belt
re-connect the electrical plug.
Reconnect battery.
All Done.

Aug 09, 2009 | 1996 Dodge Avenger

Not finding what you are looking for?
2000 Mazda MPV Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts


Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides