Question about 2000 Kia Sportage

1 Answer

Putting a starter on a 2000 kia sportage\r\nwhere does positive wire go

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 67 Answers

The positive wire always goes on to the larger bolt on the solinoid there will be 2 one big and 1 small normaly the positive is held on by a 13mm spanner size nut .

Posted on Aug 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 Kia Sportage where running but disconnect the battery now it want start


Try this:

Make sure the positive cable, makes a good connection at the battery and at the starter. Make sure the negative cable makes a good ground connection at the battery and (preferably) at the engine.
  • Check the battery the simple way, like this:
Turn on the headlights, then try to start the car.If the headlights do not dim or go out, then the battery is likely ok.
  • Check the starter and solenoid:
If the wiring looks ok, then look at the starter solenoid for a good connection, and proper voltage at the starter(10 volts minimum while cranking).
If the starter spins and no crank, the problem is most likely the Solenoid's bendix gear is stuck.
Have someone hit (not too hard) the starter while you try to start the car. This usually works by dislodging a stuck bendix gear.
  • Make a simple test of the alternator:
If you can, somehow get the engine running, measure the voltage at the battery. It should be at least 13.6 volts to properly charge the battery.

Apr 18, 2015 | 2000 Kia Sportage

1 Answer

2000 Kia Sportage will not turn over...why


Check connections to starter motor and solonoid. A wire could of been dislodged while replaceing the belt

Mar 16, 2013 | 2000 Kia Sportage

1 Answer

On the Kia Sportage 2000 starter motor there are 2 wires, to what connection does those 2 wires go to and does these 2 wires go together on one terminal? There's another wire but that is obvious. I...


both wires go to the same terminal ,the bottom terminal goes into the windings on the motor and the other two go to the top terminal and the little one to operate the solonoid

Apr 24, 2011 | 2000 Kia Sportage

1 Answer

How do I remove the starter on a 2000 Kia Sportage with 4WD?


It has three bolts that need to be removed. There is a support bar attached to the engine block and bottom of intake manifold. Remove this and the starter will drop down.

Nov 21, 2010 | 2000 Kia Sportage

1 Answer

I have a Kia SPORTAGE 2000.... wher is the


go to autozones website and type in your vehicle under parts locator section

Dec 02, 2009 | 2000 Kia Sportage

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

1 Answer

2000 kia sportage starter


Behind the oil filter

Mar 13, 2009 | 2000 Kia Sportage

2 Answers

Removal of starter for a 2000 Kia Sportage


YOU HAVE TO DO IT FROM THE BOTTOM THERE IS 1 12mm BOLT AND 1 NUT AND IT SHOULD COME OUT

Jan 28, 2009 | 2000 Kia Sportage

Not finding what you are looking for?
2000 Kia Sportage Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...