Question about 1991 Ford Festiva

1 Answer

We have a 1998 ford festiva trio wb, have lost low beam on headlights, high beam and park work, have done checked connections,lamps, switch mech and continuity of conductors, all appears ok, do you know where an electrical diagram is available online or do you have any other suggestions????

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

The best place I've found for electrical diagrams is alldata.com, but it will cost, it's not free. I'm not sure what they charge for this, but it's based on Chilton Manuals, which have electrical diagrams in them.

I can't give it to you for free, even from my online resource, because Fixya.com doesn't seem to copy and paste from that to the Fixya.com website.

Posted on Aug 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

All of my running lights and blinkers work and high beams but no low beams on my 1997 Chevrolet TahoeA


Headlamps Inoperative - Low Beams

Step

Action

Value(s)

Yes

No

DEFINITION: This diagnostic procedure should only be used if the high beam headlamps are operating properly and the low beams are inoperative.

1

Did you perform the Headlights System Check?
--
Go to Step 2
Go to Headlight System Check

2

  1. Turn the headlamp and panel dimmer switch to the ON position.
  2. Move the headlamp dimmer switch to the LOW position.
  3. Backprobe the headlamp dimmer switch connector with a J 35616-200 from cavity A to ground.

Does the test lamp light?
--
Go to Step 3
Go to Step 5

3

  1. Remove the daytime running lamp relay.
  2. Connect a J 35616-200 at cavity G5 to ground.

Does the test lamp light?
--
Go to Step 4
Go to Step 6

4

  1. Re-install the daytime running lamp relay.
  2. Backprobe cavity B at the high/low beam headlamp with the headlamp dimmer switch in the LOW position.

Does the test lamp light?
--
Go to Step 7
Go to Step 8

5

Replace the headlamp dimmer switch.

Is the repair complete?
--
Go to Headlight System Check
--

6

Repair the open in CKT 359 (PPL) between the headlamp dimmer switch and the daytime running lamp relay.

Is the repair complete?
--
Go to Headlight System Check
--

7

Replace the high/low beam headlamps.

Is the repair complete?
--
Go to Headlight System Check
--

8

  1. Inspect for an open in CKT 12 (TAN) between the daytime running lamp relay and S120, repair as necessary.
  2. Replace the daytime running lamp relay if no open was found in CKT 12 (TAN) between the daytime running lamp relay and S120.

Is the repair complete?
--
Go to Headlight System Check
--

Jul 24, 2015 | Chevrolet Cars & Trucks

1 Answer

Why wont the headights or running lights work on my 2002 Buick LaSabre?


There are several reasons why your headlamps an running lights don't work , the headlamp switch is a good one ,plus relays an the DIM - dash integrated module an associated wiring ! Here is how the headlamps work , right out of Buick factory service info !
The dash integration module (DIM) provides battery positive voltage to the signal circuits of the headlamp switch. The signal circuits include the headlamp switch headlamps on signal, the flash to pass switch signal and the high beam input. With the headlamp switch in the ON position, a ground path is available for the headlamp switch headlamps on signal circuit of the DIM through the headlamp switch. The DIM provides ground to either the headlamps high beam relay control circuit or the headlamps low beam relay control circuit of the low beam circuit. The position of the headlamp dimmer switch determines which relay control circuit has ground. The DIM supplies battery positive voltage to the relay control circuits, if the headlamps are necessary. The fuse block - underhood supplies battery positive voltage to both relay switch circuits. When the low beam relay control circuit is energized, current flow is to both low beam fuses and to the low beam headlamps. The headlamps have ground at G103 and at G401. When the headlamp high beam relay control circuit is energized, current flow is to both high beam fuses and to the high beam headlamps. The high beam circuit is divided into a left and right side circuit. The current flow of the left high beam is from the fuse to the left high beam lamp. From the lamp, the current flows to the normally-closed contact of the DRL relay to G103. The current flow of the right high beam is from the fuse to the right high beam lamp. From the lamp, the current flow is to ground at G401. When the headlamp dimmer switch lever is pulled toward the driver, the flash-to-pass switch closes. This grounds the DIM flash to pass switch signal circuit. In response to this input, the DIM energizes the HDLP HI BM relay. Both high beams remain on until the driver releases the switch handle. If the low beam headlamps were on during a flash to pass operation, the low beams remain on. The headlights may be switched to high beam with the opposite movement of the headlamp dimmer switch lever.
By running lights , do you mean park lamps or day time running lamps ?
Park, Tail, License and Marker Lamps
The park lamps, including the license lamps, are turned on when the headlamp switch is placed in the PARK or ON position or anytime the headlights are requested. The fuse block - rear supplies battery positive voltage to the switch contacts of the Park LP relay. When the headlamp switch is in PARK or in ON, the park lamp switch on signal circuit of the DIM has a ground path. The DIM provides battery positive voltage to the control circuit of the Park LP relay. When the park lamps and/or the tail lamps are ON, the DIM energizes the park lamp relay control circuit. This closes the switch contacts. Current flows from the Park LP relay to the LH PARK LP and the RH PARK LP fuses. From the fuse, the current flows to the park lamps. The left park lamps are grounded at G103, G401 and G402. The right park lamps and the right tail lamps are grounded at G103 and G401. The DIMR fuse supplies battery positive voltage to the license lamps and to the DIM instrument panel lamp fuse supply voltage - 1 circuit, for interior lamps dimming. The license lamps are grounded at G401.
The best advice I can give is that you take this to a ASE certified professional repair facility unless your a qualified automotive electric repair person !
Diagnostic Starting Point - Lighting Systems
Begin the system diagnosis with the Diagnostic System Check - Lighting Systems . The Diagnostic System Check will provide the following information:
?€¢
The identification of the control modules which command the system


?€¢
The ability of the control modules to communicate through the serial data circuit


?€¢
The identification of any stored diagnostic trouble codes (DTCs) and their status

The use of the Diagnostic System Check will identify the correct procedure for diagnosing the system and where the procedure is located.

The

Mar 15, 2015 | 2002 Buick LeSabre

1 Answer

Why doesn't my speedometer/odometer, horn and headlights work?


Which insturment cluster does your's have ? electronic instrument cluster or standard instrument cluster !

Standard insturment cluster - speedo / odometer
Speedometer/Odometer
The speedometer and odometer provides speed information based on a speed/distance pulse signal from the vehicle speed sensor (VSS). The VSS is mounted on the speedometer driven gear in the transmission.
Could be the VSS is bad .
Horn The horn system includes the following:
  • horn relay
  • horn
  • clock spring
  • steering wheel control switch harness
  • steering wheel pad horn switch, which is part of the driver side air bag module. For additional information, refer to Section 501-20B .
The horn is located behind the front bumper mounted to the radiator support.

Is the air bag light lit on the insturment cluster ? If it is the clock spring could be the problem . If not lit check the circuits from the horn relay .

VEHICLE RELAYS Operation Diagnosis .

Which headlamps don't work ? Low beams , high beams , both ?
  • The high beams are inoperative
  • Bulbs.
  • Circuitry.
  • Multifunction switch.
  • GO to Pinpoint Test C .
  • The low beams are inoperative
  • Bulbs.
  • Circuitry.
  • Headlamp switch.
  • Multifunction switch.
  • LCM.
  • GO to Pinpoint Test D .
Principles of Operation
NOTE: Due to varying wattage ratings and resulting current draw, certain aftermarket headlamp bulbs may cause the lighting control module (LCM) to shut down the short circuit protection, resulting in the low beams becoming inoperative. Verify that the headlamp bulbs meet Ford specifications.
Headlamp System The headlamp system consists of:
  • two aerodynamic halogen headlamp bulbs and retainers
  • headlamp switch
  • multifunction switch
  • lighting control module (LCM)
  • circuit wiring and circuit protection
In normal operation:
  • With the multifunction switch in the low beam position, power is supplied by the LCM to the low beam elements through the multifunction switch.
  • With the multifunction switch in the high beam position (forward detent), power is supplied to the high beam elements and to the high beam indicator in the instrument cluster.
  • When the multifunction switch is pulled toward the steering wheel, the flash-to-pass switch (part of the multifunction switch) is closed and power is supplied to the high beam elements. When the switch is released, they return to low beam operation.
  • The battery saver feature of the LCM will automatically turn off the courtesy lamps, demand lamps, headlamps, or parking lamps under the following conditions:
    • The ignition switch is in the OFF position.
    • The headlamp switch is in parking lamps ON or headlamps ON positions.
    • After 10 minutes.
Headlamp Switch The headlamp switch is a multi-position switch.
  • The positions include OFF, PARK, and HEAD.
  • With the headlamp switch in the PARK position (first detent), a signal is supplied to the LCM which powers the front parking lamps, the tail lamps, the side marker lamps, and the license lamp.
  • With the headlamp switch in the HEAD position, power is supplied to the headlamps through the LCM and the multifunction switch.
  • The panel dim switch (part of the headlamp switch) is located above the headlamp switch. The panel dim switch operates only with the parking lamps or headlamps on.
  • When the panel dim switch is held in the up position, the instrument panel lighting will progressively brighten.
  • When the panel dim switch is held in the down position, the instrument panel lighting will progressively dim.
For additional information, refer to Section 413-00 .
Headlamps On Warning Chime If the headlamp switch is left in either the PARK or HEAD position and the driver door is opened, the LCM will sound a headlamps on reminder chime when the following conditions occur:
  • The ignition switch is OFF with the ignition key out.
  • The driver door is ajar.
For additional information, refer to Section 413-09 .

Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Headlamp switch
  • Central junction box (CJB) fuse(s):
    • 6 (15A)
    • 15 (15A)
    • 21 (15A)
    • 23 (15A)
    • 27 (20A)
  • Battery junction box (BJB) HI-BEAM HEADLIGHTS (20A) fuse
  • Circuitry
  • Headlamp bulb
  • Lighting control module (LCM)
  • Loose or corroded connections

Jul 10, 2017 | 2003 Ford Crown Victoria

2 Answers

2005 Ford Focus ZX3 SES, the blue high beam indicator in the dash comes on with low beams, and goes off with high beams. The indicator is on at the wrong time! I have tried the following: The turn signal...


It sounds like you are confused about how your headlamp system is supposed to work. The DRL does not run on the High beam circuit, it runs on the low beam circuit. The fog lamps are supposed operate with the park lamps and also with the low beams, not the high beams. From your description, I would say that your system is operating as designed and you are having trouble telling High from Low. (Don't feel bad, that is why high beam indicators were invented in the first place.)

May 08, 2011 | 2005 Ford Focus

1 Answer

2001 grand caravan low beam light not working. i chang bulb already i check fuse already.


Hi Every single time I have had a failure of low beam in a headlight without failure of high beam, it has been because the lamp bulb or halogen lamp module has reached the end of its serviceable life, not because of any wiring problems. Low beam burns out first because it is on the most. If low beam is lost simultaneously in both headlights, I would check fuse first, then the headlight switch. If low beam is lost on one side only, it is almost always going to be due to the bulb or lamp module needing to be replaced. In that case, replace them in both headlights because the other one will be going kaput in short order, as well.Also if you already replaced the fuse and bulb check the headlight dimmer control switch.
Thanks for using Fixya.

Mar 14, 2011 | 2001 Dodge Grand Caravan

1 Answer

Headlight low beam does not work on passenger side of vehicle, but does when switched to driver side?


Make sure the connection at the lamp is clean and corrosion free. If corroded, clean with an electrical contact cleaner or baking soda and water then retest. Check the high-beam operation. If the light works on high-beam then you have a wiring problem on the low-beam power circuit. If neither the high nor the low-beam works then you likely have a ground circuit problem. Check the pins at the lamp connector using a Digital Volt/Ohm Meter and the appropriate wiring diagram. Voltage should be within 0.5 volts of battery voltage. Resistance to ground should be less than 5 Ohms with the ignition key off. These tests will give you a better idea as to which circuit is faulty.

Feb 02, 2010 | 1998 Ford Windstar

1 Answer

Daytime running light working fine but can not switch on the head light? 1998.


Pull the head light switch and check it for out put.Do you have high beams?Check the low beam headlight bulbs.If you have high beams,and low beam bulbs are good,replace the dimmer switch.

Nov 10, 2009 | 1998 Ford Escort

2 Answers

High beams wont turn on.


First place to start is with headlight switch. I did have a case many years ago when both high beams were blown out at once, but this is rare. When you have the headlight switch out, jump power from te low beams to the high beam contacts. If high beams come on, replace switch.
Bill

Nov 19, 2008 | 2004 Ford Explorer Sport Trac

1 Answer

Headlights


hi try having your head lamp combo switch checked sounds alot like it.

cheers
mark

May 29, 2008 | 1992 Ford Festiva

Not finding what you are looking for?
1991 Ford Festiva Logo

437 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...