Question about 1997 Chrysler Town & Country

1 Answer

How do i get the computer codes Thanks Bill

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

You need a scanner, can buy inexpensive ones for maybe 60-75 bucks or many auto parts stores will scan for you also.

Posted on Aug 29, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 01 rodeo, replaced timing belt because it was time to change it. however, the marks are right, but it will not rev up and has no power. checked the timing marks and they are correct. someone...

I would be running the fault codes to check for faulty sensors. To reset the CPU use a code reader but I suspect that will not be your problem

Oct 14, 2013 | 2001 Isuzu Rodeo

1 Answer

MAP sensor code shows fault , replaced sensor, code still goes on and off, book says to check all vacum lines for cracks or leaks. where are they all located any place to locate a diagram? Bill

After you replaced the sensor, you will have to have a scanner connected to the computer again and have the trouble codes cleared. Otherwise the original code is still causing the light to come on.

Dec 30, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

On the dash of a holden cruze (2002 Model) there is an illuminated symbol that looks like an engine, what does it mean?, Thanks Bruce

This is the vehicle's check engine light, and it means that the on-board diagnostic computer has detected a fault and stored a service code. Your Holden dealer, any reputable mechanic, and many auto parts stores can retrieve the code and tell you what part or system requires service.

Bill B.

Nov 18, 2010 | 2001 Suzuki Swift

1 Answer

P700 trouble code on 06 dodge durange. cant find what the code is. thanks

Transmission control system malfunction. Likely solenoid pack on transmission faulty. Don't leave it, get it in to a good transmission place or dealer, diagnosed properly and fixed otherwise your flirting with big repair bill later.

Aug 13, 2010 | Dodge Durango Cars & Trucks

1 Answer

Car is missing and shaking until is reaches about 45 mph.

would change the coils have codes cleared then drive it if the computer is really bad the light will come back on

Jul 29, 2009 | 2005 Ford Escape

1 Answer


Bill look under dash on drivers side find the keyless entry module, the bold numbers on the module are your factory keyless code, hope this helps

May 23, 2009 | 1995 Ford Explorer

1 Answer

Where to hook up my OBDII code reader on 2003 Tahoe?

Either a trap door in the panel under the steering wheel, or up under the dash pointing down (near the outer wall)

Jan 19, 2009 | 2003 Chevrolet Tahoe

Not finding what you are looking for?
1997 Chrysler Town & Country Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides