Question about 1992 Nissan Pathfinder

1 Answer

Put in a new starter on a 1992 path finder - 1992 Nissan Pathfinder

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 6,826 Answers

REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable at the battery, then disconnect the positive battery cable at the starter. Fig. 1: Starter removal on 4WD — 6-cylinder engine put in a new starter - 86713015.gif
    Fig. 2: Starter removal on 2WD — 6-cylinder engine 86713016.gif

  2. On 4wd models with the 6-cylinder engine:
    1. Remove the front gravel shield.
    2. Detach the oil pressure switch connector.
    3. Drain the engine oil and remove the oil filter. CAUTION
      The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
    4. Remove the exhaust manifold heat insulator.
    5. Remove the fuel tube retainer bolt.
  3. On 2wd models with the 6-cylinder engine:
    1. Remove the front right wheel.
    2. Remove the front gravel shield.
    3. Remove the exhaust manifold heat insulator.
    4. Remove the exhaust manifold.
    5. Detach the oil pressure switch connector.
  4. Unfasten the remaining electrical connections at the starter solenoid.
  5. Remove the two nuts holding the starter to the bell housing, then pull the starter toward the front of the vehicle and out. To install:
  6. Insert the starter into the bell housing, being sure that the starter drive is not jammed against the flywheel.
  7. Tighten the attaching nuts and secure all electrical connections to the starter assembly.
  8. Install all remaining components in reverse order of removal.
  9. Reconnect the battery cables. If applicable, refill and check the oil level. Check the starter assembly for proper operation.
prev.gif next.gif

Posted on Aug 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove/replace starter


Disconnect the ground on batterie and remove two bolts and remove two wires on selenoid put the new starter on and connect your wires on selenoid than put your ground on batterie job done good luck it is very simple to do...

Aug 19, 2014 | 1992 Chevrolet K1500

1 Answer

Put new selenoid and starter in 1992 ford ranger stx started up and now it won't start unless I pop start it


Have you checked the positive and negative connections at the battery, and are you getting voltage at the starter and solenoid when the key switch is in the start position ?
Have you checked the clutch safety switch ?

Jan 28, 2013 | Ford Cars & Trucks

1 Answer

2004 chevy tahoe won't turnover or start by being jumped


The ignition start circuit is the path from the ignition key in cranking mode to the solenoid on the starter. The path travels through a starter relay and a neutral safety switch before it reaches the starter.
This must be the circuit not working on your car.Make sure battery and starter connections are tight.Check for power at the starter solenoid terminal with a testlight when someone turns key to crank. If you have power there, they sold you a defective starter. If you have no power there then it could be the relay or the neutral safety switch.

Nov 28, 2011 | 2004 Chevrolet Tahoe

1 Answer

I have a 1992 chevy 1500 p.u truck - it wont start its making a clicking sound but nothing is turning over. its not the battery we put a brand new one in and it still wont work. Any ideas?


The clicking is from your starter solenoid, trying to get the starter working. If your electrical connections to the starter are tight and clean, then the starter needs removing and testing.

Oct 07, 2011 | 1992 Chevrolet K1500

1 Answer

I HAVE A 1992 NISSAN PATHFINDER AND I HAD A MECHANIC PUT IN A NEW STARTER AND IT STILL WON'T START WHEN IT GETS HOT. I HAVE TO WAIT TILL IT COOLS DOWN THEN SOMETIMES HAVE TO TAP THE STARTER. THE...


If he installed a new or remanufatured starter, I would suspect a weak battery possibly. If he installed a used starter, I would say the starter is bad. A hot engine is harder to crank than a cold engine and if the starter is marginal it will act the way you described. Try boosting your vehicle the next time it's hot, or get your battery load tested by a reputable shop that doesn't sell batteries. I have had experience with remanufactured starters that were no better than the unit I removed from the vehicle. Have him get a second reman and see if that doesn't solve the problem.

Aug 17, 2011 | 1992 Nissan Pathfinder

1 Answer

FIRING ORDER 94 6 CYLINDER PATH FINDER


hi try this site its awsome for what you need here is the link hope this helps
http://autorepair.about.com/library/firing_orders/bl-fo-7474.htm

May 10, 2010 | 1994 Nissan Pathfinder

1 Answer

Help


It sounds like you have your starter solenoid wires on your starter crossed try switching them.

Sep 06, 2009 | 1992 Buick Park Avenue

Not finding what you are looking for?
1992 Nissan Pathfinder Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...