Question about 2004 Chevrolet Colorado

1 Answer

I changed the oil and the change oil light still comes on. Is there a button that I can shut it off?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

No button to reset it, Has to be reset at an auto part store or shop.

Posted on Aug 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oldsmobile intrigue oil light reset how to m?


The oil light comes on when oil pressure is too low. Oil level too low or defective oil pump in the engine. But the most common problem is a defective oil pressure sending unit sensor on the engine. The only way to reset the oil light, is by fixing the problem. There is no reset button.

May 22, 2014 | Cars & Trucks

1 Answer

After oil change how do you shut off the change oil light


Open the fuse panel between door and dash there should be a reset button turn key to run position without starting press button till oil change light flashes and tone sounds then turns off may have to push button several times

Nov 22, 2011 | 2000 Pontiac Grand Am GT

1 Answer

My change oil display on my 2005 ford explorer i changed the oil and it wont go out


Press your reset button on the on board diagnostics which is located on the dash, keep pressing the rest button until you see "oil life" once you come to the oil life, hold the reset button until it reads "Oil Life 100 percent" release the reset button, shut the vehicle off then re start it, that will turn off the message in the message center telling you to change your oil.

Oct 18, 2011 | 2005 Ford Explorer

1 Answer

I can;t reset the change oil light on my dash of my 2007 lincoln town car I had the oil changed last week ?


This procedure work for one 2004... press mode button until oil life or change oil or change oil now is displayed press and hold mode button for 5 seconds until reset for new oil is displayed then hold reset for 2 seconds.

Additionally, I quite other comments about this subject....

Few issues have troubled technicians more than the infamous "Change oil soon light." We have even had quick lube shops send customers to me at the dealership to shut off this light.
Yes, the engineer that designed this system most certainly had flunked out of the "User Friendly" semester of college. The most common problem is between step 1 and 2 of the owner's manual. The natural tendency is that when we scroll through the menu to the "oil life XX%" mode, we lift our finger. This is where most go wrong. Once the "oil life XX%" comes up on the menu, do NOT lift from depressing the button- just hold for 5 seconds until the "Reset for new oil life" comes up. Again, do not lift your finger.

The parking assist is a different concern altogether. The parking assist light illuminated when it is deactivated- opposite of what seems logical. It was probably the same design engineer as the oil change system. If the system is disabled, (illuminated) it is intended to cycle back when the key is shut off.

Hope helps.

Jun 16, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

2007 ford 500 oil warning light comes on and just had the oil and filter changed 700 miles ago,62000 mile on car .light comes on when started ,push reset and it goes off and stays off until the next start...


When they changed the oil they did not reset the light. The car needs to be told when the oil is changed.

when the warning comes on press the setup button. it should say press reset if new. Press the reset button. It should say if new oil hold reset. Press and hold the reset button until the display changes to oil life set to 100%.

Oct 12, 2010 | 2007 Ford Five Hundred Limited Sedan

3 Answers

How to reset the change oil light for a 2007 lincoln town car. Hitting reset button doesn't do it.


FIRST press and release the setup button to display oil life= xxx
then press and hold the reset button for about 2 sec it should then display oil life set to 100%
--------------------------------
Just pressing the reset button when the change oil light comes on while driving will not reset the computer

Feb 15, 2010 | 2007 Lincoln Town Car Signature Limited...

1 Answer

I changed the oil in my 2008 Doodge Avenger, and now the change oil warning is coming on. How do I shut it off?


The following procedure should reset your oil change light:
  1. Turn ignition to the "ON" position.
  2. Quickly press button to the left of the spedometer twice.
  3. Turn ignition off. Press and hold button and turn ignition tothe "ON" position. Continue to hold button until new interval is displayed and a chime is heard.
  4. Turn ignition off.
Best of luck!
Greg

Nov 09, 2009 | 2008 Dodge Avenger

1 Answer

Shut OFF Change Oil light


look in your manual its usually a litle trick w/ your ignition key and some buttons like on toyotas good luck

Jun 22, 2009 | 2005 Chevrolet Suburban

1 Answer

Change oil light stays on after oil change


Did you also change the filter as well as the oil, and have the system flushed?

If not, do so.

Apr 17, 2009 | 2006 Chevrolet HHR

1 Answer

How to turn off change oil light on 2001 Corvette


Unless there is something wrong with you buttons the procedure is as follows:
1. Turn ignition key to ON (not start)
2. Press ENG MET button on trip monitor & release, then press it again within 5 seconds.
3. Within 5 seconds again press and hold GAUGES button until Change Oil lamp flashes.
4. Continue Holding Gauges button until lamp stops flashing & goes out.
5. You should be done, start & shut off car. If it didn't work turn off car and start from top.

Some buttons are very sensitive so try and be deliberate & steady when holding.

If that helps please rate my answers!
Brett

Mar 19, 2009 | 1994 Chevrolet Corvette

Not finding what you are looking for?
2004 Chevrolet Colorado Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...