Question about 1995 Dodge Ram 2500

Open Question

How to replace 1995 dodge ram 4x4 brake rotors

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pkthoege
  • 93 Answers

SOURCE: pull to the left, Brakes

Sounds like it was pulling before the brake job...if so the only thing you didn't replace was the rotors, I assume you turned them? and did you see hard spots on the rotor? discolored area that didn't cut the same......switch the rotors left to right and see if the problem moves or just replace them if they've been cut twice.

Posted on Dec 01, 2008

michigan man
  • 3533 Answers

SOURCE: i need a diagram for a transmissionof a dodge ram

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Posted on Mar 12, 2009

  • 79 Answers

SOURCE: Need spark plug wire to distributor diagram for 2000 dodge ram

Hi
Here is a diagram.93009452.gif

Posted on Apr 09, 2009

  • 22 Answers

SOURCE: removing the front brake rotor from the hub housing

You need to take the rotor/hub off the spindle.So you'll need to remove the wheel bearings in order for it to come off. Once off theres bolts in the back of the rotors bolted to the hub.

Posted on Apr 27, 2009

  • 66 Answers

SOURCE: 2006 dodge ram 2500 4x4 diesel replace brake pads front and back

Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Dodge Ram 2500 4X4, all 4 brakes locked up.


that's odd ,try disconnecting the vacuum hose at the booster chamber and see if they release,had a truck do that once,the master cyl.seal at the booster failed and the brakes were applied.

Dec 10, 2013 | 2004 Dodge Ram 2500

1 Answer

What causes pedal chadder on a 1998 dodge ram 1500 4X4


brake pedal? when braking? that would be warped rotors. I'd pull the rotors off have them machined or replaced and replace the pads at the same time

Mar 22, 2013 | 1998 Dodge Ram 1500 4WD

2 Answers

How to tell if ball joints are worn on a 1995 Dodge 2500 4X4. I have a shake when braking and pulls right


Hi, well when lower or upper ball joints go bad your tires will wear more tread on the inside edge of the tire and you might hear a pop or clunk when turning a corner.... but from what your describing it sounds like #1rst. the shake,since its only shaking when you brake and not all the time, tells me your brake rotors are warped and need turned( brake shop can do ) #2. if the truck only pulls right when you brake.then thats going to be in the brakes also... I would have your rotors turned and put new brake pads on it and that should fix your problem....yz-maniac.

Oct 16, 2010 | 1995 Dodge Ram 2500

1 Answer

How do I remove the rotor on my 1995 dodge 2500 4x4? My problem in the center cap holding it.


Brake Disc (Rotor) REMOVAL & INSTALLATION
  1. Raise and safely support the front of the truck with jackstands. Remove the front wheel.
  2. Remove the caliper assembly and support it to the frame with a piece of wire without disconnecting the brake fluid hose.
  3. Remove the hub and rotor assembly.
  4. Install the rotor in the reverse order of removal, and adjust the wheel bearing as outlined in Section 1.
INSPECTION If the rotor is deeply scarred or has shallow cracks, it may be refinished on a disc brake rotor lathe. Also, if the lateral run-out exceeds 0.010 in. (0.25mm) within a 6 in. (152mm) radius when measured with a dial indicator, with the stylus 1 in. (25mm) in from the edge of the rotor, the rotor should be refinished or replaced. A maximum of 0.020 in. (0.5mm) of material may be removed equally from each friction surface of the rotor. If the damage cannot be corrected when the rotor has been machined to the minimum thickness shown on the rotor, it should be replaced. The finished braking surfaces of the rotor must be parallel within 0.007 in. (0.178mm) and lateral run-out must not be more than 0.003 in. (0.076mm) on the inboard surface in a 5 in. (127mm) radius. Fig. 1: Use a dial indicator and micrometer to check the rotor for run-out and thickness 88479g83.gif
Fig. 2: A correct final rotor finish 88479g84.gif
Fig. 3: Location of the rotor minimum thickness marking 88479g91.gif
Fig. 4: Exploded view of a rotor mounting to the hub — 4WD Dakota models shown 88479g90.gif
prev.gif next.gifprev.gif next.gif

Sep 03, 2010 | 1995 Dodge Ram 2500

1 Answer

What is the torque when replacing the rotor and hub on a 1995 dodge 2500 4x4 and what is the process


Front hub nut is 265 lbs at final , I usually take it to around 100 lbs on the first go and assemble the brakes ... then when the wheel is back on the ground I will finish the torque off at 265 lbs. If you don't have a torque wrench that goes that high put a 44 mm socket on a breaker bar with a 3 foot extension and stand on it... that will get you close.

Jul 29, 2010 | 1995 Dodge Ram 2500

2 Answers

How do you replace the rotor on front end of a 2500 4x4. the pickup is a 99.


take wheel off then remove brake caliper rotor is then able to pull off yes it is that easy

Jul 22, 2010 | 1999 Dodge Ram 2500 4WD

1 Answer

I can not get the brake rotors off. Calibers are removed. Tried a puller and no luck. Do I need to remove the nut on the spindle?


Im not an expert but Ive changed the rotors on my 96 Dodge ram 1500 4X4 a couple of times (Im real hard on brakes) and as soon as I take off the caliper the rotor slides right off. Ive had problems with the rear drums coming off but the rotors should slip right off.

Jun 04, 2010 | 1996 Dodge Ram

1 Answer

Front end vibrates when braking at highway speeds


Most common cause for this is rotors that have become warped. It is not uncommon if you drive fast and brake hard OR live in hilly country or with heavy loads. The brakes get hot - the more they are used the hotter they may get. When they cool they do not cool evenly. If there is enough of the rotor left it may be resurfaced to true it. However - the thinner it gets the less heat it can handle. When rotors reach a minimum thickness (stamped on the rotor) they must be replaced.

Jan 16, 2010 | 2006 Dodge Ram 1500

1 Answer

How to replace wheel u-joints on a 1995 dodge ram 1500 4x4


remove wheel,brakes,rotor,axle nut,wheel bearing then the axle should pull right out

Jan 13, 2010 | 1995 Dodge Ram

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...