Question about 2006 Lexus Rx 330

2 Answers

2006 rx330, vehicle suddenly lost power, can't drive for more than 5 mph, check engine light is on, vsc light is on, it throw two codes, but two codes are the same p2118. is it that I have a bad fuse, which one? It happened a week ago after someone ran a battery test. Didn't find anything wrong, didn't lose power then, so I erased the code, now it happened second time and lost power, seems like it shifted into some protection mode.

Posted by on

  • gydba Aug 29, 2010

    Didn't answer any of my question at all.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lexus Master
  • 11,800 Answers

That error code signals the fact that the voltage at the battery is low - most likely because the alternator is on the verge of complete failure.
Start by cleaning the clamps on the cables to the battery (inside and out) - use wire wool and rub it in until it shines, especially on the inside. Then put another battery and measure the voltage at idle - if it's below 14 volts then you need a new alternator, if it's over that then you need a new battery..

Posted on Aug 29, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,513 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disable trac and VSC in highlander hybrid 2006 model


Disabling the light doesn't fix the problem, you should have this diagnosed by connecting a diagnostic code reader that can communicate with the traction control system, then go from there.

May 02, 2017 | Toyota Cars & Trucks

1 Answer

Hy.I'm Adrian.I have a lexus is250 from 2006 and I just changed the battery and apear the VSC CHEK LIGHT and ENGINE LIGHT.and a c1201 and p2118 error codes.please someone can help with some suggestin


Code P2118 throttle control motor is set when voltage to the motor gets below 4 volts, so perhaps this was set with old dead battery. code C1201 is a vague engine control code, and the VSC vehicle stability code is set anytime you hook up a scan tool other that the dealer's special unit. You must reset the zero point calibration for this to go away. Use your scan tool to erase all codes to see if any come back. This will not turn off the VSC light, however. Follow below procedure to reset zero point calibration.

Zero Point Calibration - "VSC" and "VSC Off" Lights - 2002 SC430 - SOLVED
________________________________________
Friends,
For the benefit of any 2002 Lexus SC430 owners, I'll post the following item dealing with "Zero Point Calibration".
After hours of troubleshooting, I came to the hypothesis that the instructions MIGHT be different from 2002 - 2005 and 2006 - 2010 models. Below are the instructions I followed and WORKED on my 2002 SC430.
If you receive the "VSC" and "VSC Off" lights on the dashboard after a visit to a mechanic (often an independent mechanic using non-Lexus ODBII equipment), this means your "Zero Point Calibration" has been erroneously reset by a non-Lexus specific ODBII tool. This might especially happen if your state requires state inspection via ODBII, and you take your Lexus to a no-name place (like a Jiffy Lube or something). Follow the steps described in Post #6 in this thread to resolve this issue:
http://www.clublexus.com/forums/gs-2...d-vsc-off.html
Note that where you see a reference to a tool called the "SST 09843--18040", substitute that "tool" for a simple jumper cable (such as a short speaker wire) or a paperclip.
Here is the relevant excerpt from the above thread:
"The solution consists of approximately 15 step .
NOTE:While performing the Zero Point Calibration, do not tilt, move or shake the vehicle.
The vehicle must remain in a stationary condition throughout the entire process.
Be sure to perform the procedure on a level surface with an inclination of less than 1%.
Explanation of symbols:
SST (4-inch wire)
DLC3 (OBD-II connector under the dash)
TS (on the top row,pin number 3)
CG (on the bottom row,pin number 5)
(See picture below)
1. Ensure the shift lever is in the ''P'' range.
2. Turn the ignition switch Off.
3. Using SST 09843--18040, repeat a cycle of short and open between terminals Ts and
CG of DLC3 4 times or more within 8 seconds (refer to the specific vehicle EWD for
TS and CG pin location in the DLC3).
4. Turn the ignition switch ON, do not start.
5. Verify that the VSC indicator light is lit indicating the recorded zero point is erased.
6. Turn the ignition switch OFF.
7. Be sure the terminals Ts and CG of DLC3 are disconnected.
8. Turn the ignition switch ON, do not start.
9. Check that the VSC warning light goes off about 15 seconds after the ignition switch
is turned ON.
10. After ensuring that the VSC warning light remains OFF for 2 seconds, turn the ignition
switch OFF.
11. Connect terminals Ts and CG of DLC3 using SST 09843--18040.
12. Turn the ignition switch ON, do not start.
13. After turning the ignition switch ON, check that the VSC warning light is lit for about
4 seconds and then starts quick blinking at 0.13 second intervals.
14. After ensuring the blinking of the VSC warning light for 2 seconds, turn the ignition
switch OFF.
15. Remove the SST from terminals Ts and CG of DLC3.
16. Drive the vehicle for at least 5 minutes to confirm Zero Point Calibration is complete."

Oct 29, 2016 | Lexus Cars & Trucks

1 Answer

My car is a 2005 Lexus rx330 after replacing my battery the check engine light came and the VSC light also


VSC is vehicle stability control make sure that the traction control is on via the button on the dash or center console

Aug 01, 2016 | Lexus Cars & Trucks

1 Answer

Rx330- check light is on and vsc light is on. Engine is shaken. What does it mean?


There is a problem with the performance of the engine, and you should have the engine computer checked for trouble codes.
Anytime the check engine light is on, the vsc is on too because the vsc uses the engine to control the car.

Aug 30, 2015 | Cars & Trucks

1 Answer

2006 Highlander - Check engine light and VSC light on. What does this mean?


you will need to hook up a scan tool, I know many parts stores will loan you one or let you use it in the parking lot, VSC could have something to do with a wheel mounted speed sensor, did you hit something? any noises, try this and see if it goes away
    • 1 Shut off the vehicle's engine and apply the parking brake to protect yourself while working on the vehicle.
    • 2 Open the vehicle's hood and examine the engine compartment. Locate the air filter box mounted to the left of the engine. The air filter box features a black exterior, square in shape, and a large ribbed intake hose.
    • 3 Check all of the small black vacuum lines surrounding the air filter box. Reconnect any disconnected or loose vacuum lines you find.
    • 4 Start the engine and drive the vehicle to clear the "VSC" warning light displayed on the dashboard. If the VSC light fails to go out after driving the vehicle normally, proceed to the next step.
    • 5 Park the vehicle, turn off the engine and set the parking brake. Open the vehicle's hood and disconnect the battery's negative cable for 15 seconds, using an appropriate size socket. Disconnecting the negative battery cable will reset the vehicle's computer and clear the "VSC" warning.

Dec 12, 2014 | 2006 Toyota Highlander

1 Answer

How do I fix 2006 RX 350 SE VSC and Check Engine, Track off - light on, any advice please.


the first thing you need to have the vehicle scanner for codes, then code will guide thrugh the repairs need it.

Oct 06, 2014 | 2006 Lexus Rx 330

1 Answer

07 lexus rx 350 with check engine light code p0304


Hi, did you ever get an answer? I have the same issue. Thanks.

Mar 23, 2010 | 2007 Lexus RX 350 FWD

1 Answer

2004 lexus rx330 what does vsc light indicate


VSC is Vehicle Stability Control. This is and electronic sensing which monitors and combines performance of braking, wheel slippage and handling, ect.
If this light comes on along with check engine light, it can be caused by a loose gas cap or faulty o2 sensor.

Nov 23, 2009 | 2004 Lexus RX 330

4 Answers

What does the VSC light on the dash mean


VSC means Vehicle Stability Control. Take the car for a scan to ease your mind.

May 20, 2009 | 2004 Toyota Solara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...