Question about 1992 Geo Tracker

1 Answer

How do line up the top gear and bottom gear after taking off the timeing belt and the gears got moved 1992 geo tracker 4 cyl

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Geo Master
  • 8,270 Answers

Align sprockets as shown below. As you put the belt on, it should be tight on the right side for proper timing with the gears in these positions. Make sure it stays on both pulleys as you release the tensioner onto the belt.

How do line up the top gear and bottom gear after - d05fa7a.gif2deb272.gif

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a diagram of 1993 Geo tracker steering gear shaft


sure, steering, gear, but which end,?
the top at steeriing wheel, shaft or bottom end.
the bottom, at box?
or the box. itself main shaft, 1 o 2?
4 total shafts driver to pittman arm.

why not post the job, what's wrong, what are you doing.
no air bags so you are safe.
ill guess at , steering box, parts because you said GEAR.

manual box or power steering box. (2 options day 1)
i have the parts cat,blow up of the box
and all photos of box setup, in the FSM.
lots and lots of photos. and drawings,
ill wait until you tell me what your doing first, then give you them.

what is the JOB ?

Jan 29, 2015 | 1993 Geo Tracker

3 Answers

93 GEO TRACKER


Check all of the battery terminals and cables and check the wires on the starter/selonoid, start from the battery and follow the cable out and check all conections , clean and tighten them and if it still does it the starter/selonoid is bad and needs replacement...

pls do rate the solution

thanks.
regards.
fixya expert team

Sep 02, 2008 | 1992 Geo Tracker

1 Answer

No just finished a valve replacement on 92 geo tracker 8v eng. set crank to TDC on #4 cyl and the cam to the proper alignment notch on rear valve cover and installed the new timing belt. However after all...


When timing belts are installed, the normal position of the crankshaft is for #1 cylinder to be at TDC. Here is a picture of the timing belt routing and the timing marks.

chuckster57_44.gif

Jun 04, 2011 | 1992 Geo Tracker

3 Answers

Bad problem, runs an revs fine in nutral and park. as soon as i put it in gear it losses power and idel will drop to the point to staliing and will not move. put it back in gear and after playing with the...


The possible problem is the timimg may have jumped due to worn tiing belt i would look there first
anthoer possibility could be gas is bad and not enough octane left to sustain the extra power needed

Feb 05, 2011 | 1992 Geo Tracker

1 Answer

Am Replacing Timing Belt On 1990 GEO Tracker 4x4 1.6 motor & am trying To Find where my timing marks should be ( belt broke )


most of the time there will be one mark on the crank pulley gear and the one on the cam pulley gear.usually a dot or a straight line.

Apr 17, 2010 | 1990 Geo Tracker

1 Answer

Timing belt replacement


camshaft timing mark at 12 o"clock, align cam shaft timing mark to ( v ) cut on top of back timing cover, crank shaft gear align 12 o'clock key way up, there will be a mark on the outer edge of gear, on housing at 12 o'clock there will be the timing mark align that mark to crank gear , install belt and your done.Good luck.

Dec 27, 2009 | 1990 Geo Tracker

1 Answer

My 91 geo tracker has jumped time .how can i get it back in time?


remove Timing Belt covers set Top Dead center cyl one align cam mark and set tension

Dec 23, 2009 | 1991 Geo Tracker

2 Answers

Timeing belt for 92 geo metro 3 cyl


The timing marks are as follows
1. there is a "V" on the cylinder head cover.
2. Timing mark on camshaft timing belt gear
3. "Arrow mark" oil pump case
4. Punch mark on crankshaft gear.
DON'T MESS UP! THIS IS AN INTERFERENCE FIT ENGINE! IT WILL BEND VALVES!

Apr 06, 2009 | 1992 Geo Metro

2 Answers

1993 geo tracker 5 speed wont go into gear


in the drive way, i presume and not moving?
what it does correct is just as important as wrong.

under the car is a free play adjustment.
do that
http://carfix.stufftoread.com/
go here, and pick clutch section.


Feb 23, 2009 | 1992 Geo Tracker

2 Answers

My 1990 geo tracker wont start


STARTER RING GEAR, TEETH MISSING?

Oct 07, 2008 | 1990 Geo Tracker

Not finding what you are looking for?
1992 Geo Tracker Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...