Question about Ford F-150

1 Answer

Im converting a 91 f150 to a 94 f150 and i badly need wiring diag for both vechicles . the harness was chopped lol .

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,002 Answers

You can get both wire harness diagrams from faxonautoliterature.com. These are Ford dealer manuals so should be correct. You can get them for $40 to $50 for the pair. I've used them before and had excellent service. Hope this helps.

Posted on Aug 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the wire colors for a 2006 chrysler pacifica tailight harness?


The wire colors should be Yellow, Black, White and Green. Do not cut or splice anything into this harness. Use the trailer lights Tap connector that is already in the harness. It is located in the left frame rail near the rear bumper. The converter is a plug and play operation. No splicing is needed. Simply unplug the harness at the Tap connector and plug the converter T plug in series with the existing harness.

Jun 20, 2017 | Chrysler Cars & Trucks

1 Answer

Is there a way to find a schematic diagram for a lucino 2000 speedometer? Mine is not working, replaced with an used one but want to repair original


BAD VECHICLE SPEED SENSOR WILL CAUSE THE SPEEDOMETER NOT TO WORK.CHECK SPEED SENSOR WIRE HARNESS MAKE SURE WIRE HARNESS NOT DAMAGED OR DISCONNECTED.

Sep 10, 2011 | 2000 Nissan Sentra

1 Answer

I have a 1995 maxima that shakes and cuts out really bad when it is in drive or reverse but if i put it in neutral it stops shaking and cuttin out any ideas?


on the right side where the timing belt cover is there is a fat wire harness...over time from the motor rocking back and forth on the motor mounts will wear even short or break these wire diesect the harness and inspect......a simple diag test is to put it in nutral and manualy rock the the motor back and forth front to rear with a long bar to see if acts up doing this if not ...it may be a internal transmission tourque converter locking up issue...

Apr 27, 2011 | 1995 Nissan Maxima

2 Answers

Abs and brake light on -


you need to check if the breaks are wearing out...
Good Luck!

Oct 11, 2010 | 2004 Chevrolet TrailBlazer

2 Answers

1999 Yukon


It should not be too hard but there are special sockets to clear the wire, you might get by with a wrench of the correct size, they are either side of the bulge in the front exhaust pipes (the cat converters) and either side of the transmission, are you sure you need all 4?

Nov 01, 2009 | 1999 GMC Yukon

1 Answer

Wiring Problems?


If the chopped and taped wiring was done by the shop that worked on it, and it worked after they were finished, It's likely that they did the right job (short of replacing the entire harness) but may have done a sloppy job, resulting in your present problem. Removing burned connectors and joining wires is OK, but they should be soldered and carefully taped, otherwise connections can break, or shorts can happen. Check a few connections they made...If not soldered, either bring it back to them and have them do it correctly, or get out your soldering gun and one by one, solder them yourself. One important point though...If you find any wiring that is beginning to melt, then they have fixed the result of the problem but not the cause...That will then need further diagnoses.

Apr 17, 2009 | 1999 Chevrolet Blazer

1 Answer

Old owner chopped blower motor wiring - need pinout for resistor


It might be beneficial to you to go to a scrapyard and take a look at one that hasn't been chopped up! You may even want to buy whatever has been removed while you are there!

Feb 19, 2009 | 1997 Jeep Grand Cherokee

1 Answer

Ineed a wiring diag


My son has a 91 camaro rs and in the Chilton manual there are a lot of wiring diagrams but I need to know which one you need. The pictures are very small and hard to read but I can send you the one you need.

Jul 26, 2008 | 1992 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...