Question about 2008 Chrysler Sebring Convertible

Open Question

When i go to put my top down the dash reads secure cargo shield. what does that mean

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: connvertible top malfunction chrysler sebring2008/set cargo shield door signal

Open the trunk & reposition the folding cargo shield tray the top sits in when it is down. There is a small switch in the tray's mounting notch that indicates when the tray is in place to recieve the lowered top.

Posted on Aug 26, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 thunderbird top will go up but not down.


Do you know what a wiring diagram is an how to read it ? How to do electrical testing of the circuit with a DVOM - digital volt ohm meter ?
free wiring diagrams http://www.bbbind.com/free_tsb.html
Enter your vehicle info year ,make , model an engine size . Under system click on body & accessories ,then under subsystem click on convertible top . Then click the search button , then on the blue link . You will see two relays , one for up an one for down .Located in AUX relay box ! This is under the dash , you maybe able to look up under the dash an see it . Change relays , just because it clicks doesn't mean it's good . Have you had any aftermarket electronics put on the vehicle ? Somebody alter wiring etc...

May 02, 2017 | 2002 Ford Thunderbird

1 Answer

Driving noticed the security light was on said service security system shut off tried to start it didn't start.tried to replace fuses to disconnected the battery to reset security system.


What year, make and model ?
top speed cut off ?
if you were in a GM (say a camero) and you hit 117 mph the car will shut down.
it should how ever restart after wards

Apr 29, 2015 | Cars & Trucks

1 Answer

2006 Jeep Liberty- Why won't it roll (if pushed ) in Neutral? Won't start, but dash lights & security works !?


wow cathy 4 post now.
get it jump started, does it start now?
charge the battery to 12.6vdc rested
does it crank now, you mean it wont crank or
cranks robustly but will not start
or cranks and runs for 3 seconds.
is the IMMO light off, it has its own lamp, mine is sold read, no words, no icons, just red. if on, it WILL NEVER RUN.

key on
cranks does it crank.???
if not jumper start it. if IMMO is off.

Aug 28, 2014 | 2006 Jeep Liberty

1 Answer

Needing information on removing a heater core from a 2012 Chrysler 200


how to? that it the full steps, out and in,,>????
there is lots of information on this....
not in warranty? huh?
and how could IT be bad so soon?? no way/ ,huh?
why not post the symptoms and not guess. the below HORROR
posted to show 2 days lost work (life)
buy the FSM and read the HVAC chapter. every word
or alldata.com , same deal. look, read and decide,
oops I cant to this.....?


parcial excerpts. to prove case.
quote:
The HVAC housing assembly must be removed from vehicle for service of the heater core.

housing out: 101:
Disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in an accidental airbag deployment and possible serious or fatal injury.

WARNING

Refer to the applicable Warnings and Cautions for this system before performing the following operation and . Failure to follow these instructions may result in possible serious or fatal injury.

NOTE

The HVAC housing must be removed from the vehicle and disassembled for service of the heater core, A/C evaporator, air intake housing and the mode-air and blend-air doors.

NOTE

LHD model shown in illustrations. RHD model similar.

Heat Shield - Unified Line 08 JC

Heat Shield - Unified Line 08 JC

Disconnect and isolate the negative battery cable.

Recover the refrigerant from the refrigerant system (Refer to Heating and Air Conditioning/Plumbing - Standard Procedure).

Partially drain the engine cooling system (Refer to Cooling - Standard Procedure).

Remove the top nut (2) that secures the heat shield (3) to the stud (1) located on the dash panel.

NOTE

Two slots are provided at the bottom of the heat shield to aid in heat shield removal. Complete removal of the two bottom heat shield retaining nuts is not required.

Reach behind the engine and remove the two bottom nuts the that secure the heat shield to the studs located on the dash panel and remove the heat shield. Rotate and tilt the heat shield as required.
(capture the FREON as required by USA LAWS, Illegal for DIY person to do. so...)
Unified Liquid and Suction Line to Evaporator 08 JS

Unified Liquid and Suction Line to Evaporator 08 JS

Remove the bolt (1) that secures the A/C liquid and suction line assembly (2) to the A/C evaporator (3).

Disconnect the A/C liquid and suction line assembly from the A/C evaporator and remove and discard the dual-plane seals.

Install plugs in, or tape over the opened refrigerant line fittings and the evaporator ports.

Disconnect the heater hoses (4) from the heater core tubes. Install plugs in, or tape over the opened heater core tubes to prevent coolant spillage during housing removal.
HVAC Housing to Dash Panel Nut

HVAC Housing to Dash Panel Nut

NOTE

Make sure to remove the five bolts that secure the HVAC housing to the instrument panel support prior to removing the instrument panel from the vehicle.

Remove the instrument panel (Refer to Body/Instrument Panel/PANEL, Instrument - Removal).

Remove the rear floor ducts (Refer to Heating and Air Conditioning/Distribution/DUCT, Floor Distribution - Removal).

Remove the condensation drain tube (Refer to Heating and Air Conditioning/Plumbing/TUBE, Condensation Drain - Removal).

Remove the nut (1) that secures the passenger side of the HVAC housing (2) to the dash panel (3).

NOTE

Use care to ensure that the interior is covered in case of loss of residual fluids from the heater and evaporator cores.

Pull the HVAC housing rearward and remove the HVAC housing assembly from the passenger compartment.

at the least, and for sure , things will break, as you work.
get lost, or not figure out how to put it ALL BACK

Remove the HVAC housing assembly and place it on a workbench (Refer to Heating and Air Conditioning/Distribution/HOUSING, HVAC - Removal).

Remove the left side front floor duct (Refer to Heating and Air Conditioning/Distribution/DUCT, Floor Distribution - Removal).

NOTE

If the foam seal for the flange is deformed or damaged, it must be replaced.

Remove the foam seal (1) from the flange (2) located on the front of the HVAC housing (7).

Remove the screw (8) that secures the flange to the front of the HVAC housing and remove the flange.

Remove the screws (3) that secure the heater core tube retaining brackets (6) to the side of the air distribution housing (4).

On RHD models, remove the air distribution housing from the HVAC housing (Refer to Heating and Air Conditioning/Distribution/HOUSING, HVAC - Removal)

Carefully pull the heater core (5) out of the driver side of the air distribution housing.
end excerpt.

May 13, 2014 | Cars & Trucks

1 Answer

Connvertible top malfunction chrysler sebring2008/set cargo shield door signal


Open the trunk & reposition the folding cargo shield tray the top sits in when it is down. There is a small switch in the tray's mounting notch that indicates when the tray is in place to recieve the lowered top.

Aug 25, 2012 | 2008 Chrysler Sebring

1 Answer

No heat or cold air will come out of my2004 Mitsubishi Galant. I took off the dash panel behind the glove box to get to the Blend Door Motor, but after turning the air from hot to cold at various speeds,...


Does the air blows through the dash board vents. Does the selector is functional, that means you can force the air stream through wind shield, or vents or down to the legs. If these things are OKthen check CONTROL PANEL.
Remove the trim plate surrounding the center instrument panel. Detach the electrical connectors and remove the control panel.

Read more: How to Troubleshoot the Air Conditioning in a Mitsubishi Galant | eHow.com http://www.ehow.com/how_4520422_troubleshoot-air-conditioning-mitsubishi-galant.html#ixzz0yf04FfuE

Sep 05, 2010 | 2004 Mitsubishi Galant

1 Answer

The man computer will not record sensor or catalytic activity, Reads "not ready".Want to replace computer, where is it? under dash in side kick panels?


1 Remove the cover of the main fuse box on the side of the dashboard. 2 Remove the knee shield above the pedal assembly. 3 Lift out the air duct to facilitate access to the relay holder behind it. 4 Remove the screw securing the relay holder and press the holder down.
The Integrated Central Electronics (ICE) module is mounted above the relay holder. 5 Install in reverse order.

Aug 18, 2009 | 1996 Saab 900

Not finding what you are looking for?
2008 Chrysler Sebring Convertible Logo

Related Topics:

679 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...