Question about 1995 Mitsubishi Mirage

1 Answer

My throttle likes to stick close a little bit.. just at the close position ... what might it be? its never happen before, just recently start hapening

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 435 Answers

If the accelerator cable is loose ,it might to that.check it and adjust it.

Posted on Aug 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford five hundred replaced battery went into engine failsafe mode n will only idle no throttle response I replaced throttle body assembly just sits and idles


try using the scan tool to reset the ECM program
code p 2104 refers to throttle actuator control(TAC) system---forced idle mode ===causes ---wiring--TAC motor ---APP ensor--ECM
code p 2112 refers to throttle control actuatorTAC system---actuator stuck closed ===causes ---throttle body, throttle valve tight/ sticking
or TAC system--circuit malfunction===causes wiring short to positive ---short to ground ---throttle position sensor--- ECM

Feb 21, 2016 | Ford Cars & Trucks

1 Answer

Hight idle


Bad idle solenoid. Located on throttle body. It's black. Plugs in to wiring cable. You need a torx bit to remove. It's a cheap and easy fix. Also, get some throttle body cleaner and a tooth brush. Saturate the inside of the throttle body with cleaner and scrub out the black soot. Do this with throttle body in wide open position. Be sure to clean the edges of the butterfly good. They soot up and stick preventing throttle body from closing all the way.

Dec 15, 2014 | 1995 Jeep Wrangler

1 Answer

Engines races at 1500 rpm and up. any solutions ???


check to make sure the throttle valve Is not sticking open and not fully closing as this can cause a higher than normal idle. check to see if its dirty and clean it with throttle cleaner and a tooth brush this will allow the valve to close and not be gumed up. another thing to check is for a vacume leak like maybe a bad pcv valve. just some places to check out.

Mar 06, 2014 | 1995 Oldsmobile Cutlass Supreme

1 Answer

After starting car iin morning when you frist push gas petal it sticks with a little pessure it breaks loose and car darts forward. once operated it works fine throu driving event.only happens when it sets...


The throttle body is likely a little worn and causing the throttle plate to become jambed in the bore.Adjusting the minimum air rate up a bit will cure the symptom

Sep 06, 2011 | 1999 Buick LeSabre

1 Answer

I have got a Renault Trafic 2.0 16v and the throttle sticks open!


Its a plastic accelerator pedal type !
replace the pedal sensor

give it a good service
check setting or replace TPS

index-vapkxqg200hwgpbhetruj2b0-3-0_1.jpg222-vapkxqg200hwgpbhetruj2b0-3-2.jpg

Mar 22, 2017 | 2004 Renault 181

2 Answers

Throttle sticks at times when starting out. Hear a popping sound and throttle moves easily then


there is a throttle-stop, this prevents the throttle valve getting stuck in the bore, put simply the valve is a perfet fit and if it fully closes it is liable to get stuck in that position, so a "stop" is employed to keep the throttle just a tiny bit open, but without increasing the idle speed, it is similar to an idle-control screw. tighten this a little, so it keeps the throttle a little more open - check this diagram to find the stop adjuster screw.09aa699.png

Nov 06, 2009 | 2000 Chevrolet Silverado

1 Answer

When driving my gas pedal goes out. If I press


throttle position sensor most likely...

Oct 03, 2009 | 1997 GMC Sierra

2 Answers

96 Chrysler LHS shuts off when I slow down


IF IT WAS A FUEL FILTER IT WOULD ACT LIKE THIS ALL THE TIME. GO TO AUTO ZONE OR ADVANCED PART STORE AND THEY WILL SCAN IT FOR FREE.BECAUSE IT COULD BE A EGR VALVE STICKING OR A THROTTLE POSITION SENSOR OR A {A.I.S MOTOR].

Jan 17, 2009 | 1996 Chrysler LHS

Not finding what you are looking for?
1995 Mitsubishi Mirage Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...