Question about 2007 Nissan Armada LE
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
These can be a "bugger"... Once you have the 2 screws out, I usually get a small screwdriver wrapped in a rag between the lamp and the quarter panel (on the side of the vehicle) and gently pry the lamp straight towards the back. You might think that something is going to break and just when you think it will for sure, it will pop loose and the lamp will be in your hands, so be ready to catch it.
Nissan Scope Certified Technician- 10 + years in Nissan dealership
Posted on Nov 03, 2008
SOURCE: Shake in steering wheel
Hi! Although my collegue has pointed out the possibility of Discs being warped or out of true? Have you thought of the wheel balancing? also have you tried changing the rear wheels to the front? you may have a well imbalanced wheel or a Tyre with a side wall defective i.e. an Egg? (Buldge). Another problem on big tyres is they don't seat correctly, check the beading is settled in fully.
Hope this helps!
Posted on Jan 04, 2009
My Death Wobble started immediately after I installed a set of Coil Spring Spacers (to lift 1.75 inches). Turned out, the DW was because while changing the height, I also lowered the CASTER angle in the front end. So, to fix it, I could have purchased a set of eccentric bolts for $50+. Instead I went out and purchased a piece of 1.5 inch flat bar for $10 from OSH. I cut out 4 1.5 inch squares. Then i drilled 7/16 inch holes centerline, but close to one side (in exactly the same place) on all for squares. I then removed the lower control arm bolts, nuts and washers. I installed these square offset washers I made so the front axle would be pushed forward (to increase the Caster angle). The toe setting changed a bit, so I reset them to about 1/8 inch toe in. After driving my Jeep, I noticed there is no more DW. The steering wheel was off center, but after 3 attempts, I have that perfectly centered. I have every intension of having the alignment checked, but not till after I find the new tires I want. If anyone is interested, I can draw out and photograph the cure and send it to you. My e-mail is bb62471(at)yahoo(dot)com.
Posted on Feb 13, 2009
SOURCE: shaking while braking
I DON'T KNOW IF THIS WILL HELP BUT NARROW IT DOWN,WHEN BRAKING WHAT SHAKES,STEERING WHEEL SHAKES BACK AND FORTH IT WOULD BE A FRONT BRAKE ISSUE,MAKE SURE CALIPER HARDWARE IS OK,AND CALIPER SLIDE PINS ARE FREED UP,IF THE WHOLE CAR SHAKES IT'S THE REAR BRAKES,PINS SLIDER AND HARDWARE ON REAR ALSO,HOPE THIS HELPS
Posted on May 21, 2009
i depends where you are and where you take it to. look in your manual and see what needs to be done and figure it out from there. it usually tells you what the scheduled maintenance items are
Posted on Mar 16, 2010
Tips for a great answer:
Jan 30, 2016 | 2006 Nissan Armada
Jan 11, 2013 | Chrysler Concorde Cars & Trucks
Sep 30, 2012 | 2007 Nissan Armada LE
Aug 27, 2012 | 2004 Mitsubishi Galant
Sep 15, 2010 | 2004 Nissan Armada
Aug 04, 2010 | 1997 Nissan Maxima
Apr 19, 2010 | 2007 Nissan Armada LE
Jul 12, 2017 | 1998 Oldsmobile LSS
Sep 10, 2008 | 2000 Toyota Camry Solara
Jul 03, 2014 | 2007 Nissan Armada LE
46 people viewed this question
Usually answered in minutes!