Question about Fiat 124

1 Answer

How to replace seals on Fiat Palio 1.6 clutch master cylinder / replace cylinder. Where is it? How to remove it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to check the cylinder under the steering and replace it then problem solved

Posted on Dec 17, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

motor1258
  • 6674 Answers

SOURCE: remove master clutch cylinder on 1992 bmw 325i

Perhaps this link will be of some help.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528004a3c7

Posted on Feb 18, 2009

  • 1201 Answers

SOURCE: replacing the water pump on a fiat palio 1.2 2001

Go to an auto parts store and get a haynes auto repair manual for your car, about $17.00, it shows some illustrations, but gives a step by step procedure on how to remove and install, good luck.

Posted on Feb 25, 2009

  • 2 Answers

SOURCE: PEUGEOT 406 LX DT 1998 2088 CC CLUTCH SLAVE CYLINDER

I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.

Posted on Feb 26, 2009

stargazer406
  • 2 Answers

SOURCE: Fiat Palio-1.2 ELX (Petrol) clutch ''not-working''

Even I had this problem. After sometime engaging gear was difficult. There are two reasons. First, it could be leakage of servo fuel/brake fluid from the master cylinder on the clutch side or it could be due to the wear of the pressure plate.

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Adjust clutch pedal


the 2008 Fiat Palio 1.2 has a self adjusting
hydrualic clutch pedal system

the brake resiviour fluid has to be full
have to bleed the air out of the system at the slave cylinder

if there is a leak or by passed the internals of master or slave
those parts need to be replaced

26287046-co0ugis0ikjje40kcl2cdjwj-2-0.jpg

26287046-co0ugis0ikjje40kcl2cdjwj-2-1.jpg

Sep 20, 2016 | 2008 Fiat Palio 1.2

1 Answer

On my fiat stilo only pressure at the bottom end of the clutch pedal


check for fluid in the reservoir id hydraulic as it appears as if it needs bleeding
check / replace the master cylinder / slave cylinder
if it is a cable operated clutch then replace the cable.

Jun 25, 2015 | Fiat Cars & Trucks

1 Answer

Fiat Palio 1.2 firing order


didnt change them 1 by one, you bad boy.

id get the real engine name and google that or buy the FSM book.
at FIAT.

1.2 F.I.R.E engine.
comes in 2 favors
  • 8v SMPI VVT (2007 - current)
  • 16v SMPI (1998 - 2009)
most non boxer engines, are 1,3,4,2 (but this is pcm job not you )
google shows
IT'S WASTED SPARK SYSTEM !
google hit #1
It's cast into the cylinder head. Look across from the passenger side of the car- you'll see 2314 just above the coils.

sounds like this engine is with a COIL pack, You never said.
and with a twin pack , all 4 bangers are wasted spark.
so 2nd 3 fire on one coil (in series) and 1and 4 fire in tandom.
but the PCM sets order. not you,
it only needs to have to pack wired right.
and is clearly marked on most better made coil packs
did you look first.?

---------------------------------------------------------------------------
one more google poster , no FSM. shows
coil towards the front of the car is cylinder 2 and 3
coil towards the back of the car cylinder 1 and 4
as shown below

make sure you have the plugs to the coils the right way round thou i

4 ----[o]4
1 ----------------[o]1
2 ------------[o]2
3 --------[o]3

-----------------------------------------------------------------
me.....
when the PCM fires coil 1/4 , it better be wired to 1 and4 or
it will not run. (ir shakes like a wet dog)
simple as can be.

yes, the front cylinder is #1
now where is front. you say?, that be, on the crank pulley end.
not the clutch.side.

if still confused a drawing is easy to make.
1sparkfront, to 1 coil
2 spark to coil 2
3 spark to coil 3
4 spark to coil 4. rear cylinder is 4.
1,2,3,4 front to rear.

Jul 15, 2014 | 2008 Fiat Palio 1.2

1 Answer

Fiat palio ignition timing


its marked on the coil
and on the valve cover
its a wasted spark system.
the coil is marked (if not sub coil)
2314

1 goes to 1 front cylinder spark.
2 goes to 2.
3 to 3
4 to 4 rear spark.
the ecu knows the order but the wires MUST be right.
#1 spark is closest to front engine pulley, (belt side)
#4 is rear.

Jul 15, 2014 | 2005 Fiat Palio

1 Answer

I have a Fiat Palio 2002 and off late I find the gear shift getting stuck - means I cannot change gear when the engine is running. The gear is smooth when the engine is off.


the clutch plate is burnt and needs replacing.. Thats why it works when the car is cool or aint running. as soon as it gets hot,, the seal of the metal has burnt out.. meaning the metal binds making it hard to shift.. Change the clutch play,, you'll be fine!

Mar 08, 2010 | Fiat 124 Cars & Trucks

1 Answer

Fiat Palio-1.2 ELX (Petrol) clutch ''not-working''


Even I had this problem. After sometime engaging gear was difficult. There are two reasons. First, it could be leakage of servo fuel/brake fluid from the master cylinder on the clutch side or it could be due to the wear of the pressure plate.

Feb 28, 2010 | 2006 Fiat 124

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

627 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fiat Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Fiat Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...