Question about 1991 Chevrolet S-10 Blazer

Open Question

Belt diagram for 91 s10 blazer - 1991 Chevrolet S-10 Blazer

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
dennymulford
  • 1055 Answers

SOURCE: 91 s10 blazer engine surges warm and cold, stalls

tps sencor or maf sencor

Posted on Jan 24, 2009

Ad
  • 1 Answer

SOURCE: how do you remove a starter from 91 s10 blazer 4x4

I have done this twice on my 1991 S-10 Blazer 4x4 with automatic transmission and 4.3 v6. This procedure and it works 100%. It is mean to do, but this method does 100% work.
1.) First disconnect the positive battery cable.
2.) Now look at where the positive battery cable is clamped to the frame below the battery and unclip the cable there. This is so you can get slack on the positive battery cable. Now pull the positive batter cable down as far as you can toward the frame. This is done from the top side with the hood open.
3.) Now go unneath and take out the dust cover bolts 15mm and the dust pan will be loose, this is so you can shift the dust pan around. Don't try to completely remove the dust pan, you only need it to be loose.
4.) Now loosen and take out the two starter bolts 14mm and the starter will drop down. Now get a little rough with it and the starter will pass by the loosened dust cover and the starter will fall out. Watch out at this point that stress is not too great on the wires going to the solenoid switch. You don't want to break these two wires from the wight of the starter pulling on them.
5.) Now pull down the main battery wire to get you some wire slack to the starter. you will be able to pull it down maby 3 inches. This is enough to allow you to undo the two wires on the solenoid.
6.) The starter will now completely come out. Keep in mind that you must move the loosened dust cover form side to side to make a clearance so the starter will come out.
7.) Now compare the old starter to the new one that you have gotten so to be sure you have bought the correct starter. I got my starter form an Advance Auto Parts store (no connection to them whatsover) It was a World Parts brand part number P6416S with the solenoid. I think the generic part number would be a 6416S (S means with solenoid switch attached).
8.) Now connect the wires back to the new starter. Making sure they are shorting out against anything.
9.) You will now put the new starter back, ( with the wires connected). To do this you will have you will have to shake and move around the dust cover so it can clear its way back up in there.
10.) My starter came with 5 or 6 shims, I did not use any of them and my starter worked perfectly and meshed fine. I would not add any shims at all unless you absoulty have a reason to have to.
11.) I am 60 years old, and my son and myself did this yesterday 04-18-09 while laying on the ground on our backs. If you could do this over a ditch it would be better, but a flat ground ground will work, but it is a tighter area to work in. My son was able to lift that heavy starter back up in the hole, since I was played out at this time. A lift would be nice, but not needed.
12.) I wanted to add this real life solution that really actually works so that maby someone else can benefit from this. It is not to hard, but can be done. Keep in mind the secret is taking out all of the bolts from the dust pan so it can move around, and getting the positive battery cable loose so you can get some slack with it. Yes don't forget to re fasten back on the battery cable after you have finished.

Posted on Apr 18, 2009

csmock132
  • 4669 Answers

SOURCE: 91 s10 blazer tach signal wire

Coming off the coil there are two plugs both with two wires. One plug goes to the distributor. The other plug is the one you want. Tie into the white wire. Sometimes you will find a spade connector already hooked to this wire, hook to that.

Posted on May 26, 2009

  • 495 Answers

SOURCE: need the fuse diagran fo chevy blazer s10 4wd 1991

go to autozone.com, enter your vehicle specs, and follow the prompts for the repair section, then to electrical diagrams..........and its FREE!

Posted on Jul 27, 2009

tbirdfan1
  • 3051 Answers

SOURCE: need firing order diagram for 91 s10 blazer

991 Chevy S10 firing order
The firing order for a Chevy s10 depends on which engine you have.
1.9L engine the firing order is: 1-3-4-2 . Distributor rotates counterclockwise.
2.0L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise.
2.5L engine the firing order is: 1-3-4-2 . Distributor rotates clockwise.
2.8L engine the firing order is: 1-2-3-4-5-6 . Distributor rotates clockwise.
4.3L engine the firing order is: 1-6-5-4-3-2 . Distributor rotates clockwise.

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Chevy S10 Blazer Serpentine Belt replacement


You use a breaker bar to move the tensioner, remove the belt and use the tensioner to put it back. You draw the belt and pulleys on a sheet of paper before removing, otherwise there should be a small diagram of the belt and pulley positions on the fan shroud or radiator support.

Jun 25, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

I need diagram for firing order on a 91 s10 blazer 4.3 2wd


For the 1991 Chevrolet S10 Blazer 4.3 V6, Both: 2WD AND 4WD:

Firing Order:

1-6-5-4-3-2

Cylinders:
.......(
back).......
|..6..|.......|..5..|
|..4..|.......|..3..|
|..2..|.......|..1..|
......(front)

Distributor:
....(back)
(+).4...3
5...........2
..6...1..(+)-screw
.....(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Apr 12, 2010 | 1991 Chevrolet S-10

1 Answer

I need a serpentine belt diagram for a 91 gmc blazer with ac


Hello there and welcome to fixya:
in the 1991 series the blazer and the jimmy all used the same routing
i have provided you with the routing diagram below
cda0eb0.jpg

Feb 25, 2010 | 1998 GMC Blazer

1 Answer

91 chevrolet s10 blazer heater core access?


not really. IT is under the dash on the passenger side. You should put some plastic down or pull the carpet or it will get soaked with anti freeze

Oct 01, 2009 | 1991 Chevrolet S-10

1 Answer

Belt diagram for 99 chev blazer s10


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINKS. It has the Belt Diagrams you will need.

I'm not sure if you have the Blazer or the S10; however I have included both Links below.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies.
For the Blazer:
http://www.2carpros.com/car_repair_information/year/1999/make/chevrolet/model/blazer/1999_chevrolet_blazer_drive_belt_routing_diagram.htm
For the S10:
http://www.2carpros.com/car_repair_information/year/1999/make/chevrolet/model/s10_pickup/1999_chevrolet_s10_pickup_drive_belt_routing_diagram.htm

Jun 26, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1991 Chevrolet S-10 Blazer Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...