Question about 2002 BMW 7 Series

1 Answer

How to replace low beam bulb on 2002 745li BMW

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

If u do that and it still dont work then what do i do

Posted on Oct 14, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
j_del
  • 1586 Answers

SOURCE: burned out headlight/bulb bmw 1991 325i 2dr

It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.

Posted on Oct 31, 2008

  • 21 Answers

SOURCE: My son's 2002 BMW 745LI, Zenon type, left side,

well can be one of the 3 components in the zenon lights system, the first thing to check is the bulb, be careful dont touch it with bare hands , second thing is the Burner electronic Item and the last thing is the Module ( electronic ) your best option is to take it to any bmw authorize delaer , i had the same problems and was the module, the previous owner use to wash the engine and water got inside de module , i replace the module , the burner the bulbs ( 4 of them ) at a 950.00 cost from dealer., is not cheap, dont buy zenon buls at regular autoparts are not BMW factory item the durabily and the light system is made with cheap and low quality materials. if you have a Bimmer keep it right !

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change a low beam headlight blub on a 2004 bmw


Low and high beam are in the same bulb

Dec 12, 2014 | BMW Cars & Trucks

1 Answer

I have a 2002 BMW X5. First the left low beam stopped working and now the right low beam doesn't work. I still have high beams. Could this just be a fuse. Are th.ey fused separately. Where are


replace bulbs newer models are double contacted, normally if a lot of vibration and knocking around occurs this could short out and have it blown, also you may want to chek for slack connection on the contacts for the bulbs, again a problem due to vibration

Mar 05, 2012 | 2002 BMW 5 Series

1 Answer

I have a warning that indicated left low beam malfunction. How do I resolve this issue.


  • It means the low beam is out on the left side of your vehicle. You will need to replace the bulb and things will be back to normal.
  • Changing the bulb on this vehicle is more troublesome than most vehicles.
  • I think on the 2006 750Li you have to actually loose the bumper a bit to get to the headlight to wiggle loose. Some of the newer BMW's are made so the bumper comes up on the bottom of the headlight assembly just enough to make the bumper have to be loosened to be able to get the headlight assembly out enough to change the bulb.


Regards, Tony

Jun 20, 2011 | 2006 BMW 750Li

1 Answer

How to adjust halogen headlights on bmw z4


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Sep 14, 2009 | 2006 BMW Z4 Roadster

1 Answer

Check low beam light - light goes on and off - wiring issue?


MAY TRY CLEANING THE BULB CONNECTION WHERE THE BULB SITS ON THE PLUG IN OR CHECK FOR A BAD OR LOOSE GROUND WIRE

Apr 21, 2009 | 2001 BMW 5 Series

2 Answers

2002 BMW 525 Low Beam Headlight Replacement


I just replaced the low beam bulb on a 2002 525i. The assembly turns about one quarter of a turn to remove and then the bulb pulls straight out. It is a tight fit and the plugs are longer than you would expect. Remember to wear gloves or to use something to avoid touching the bulb. Anything left on the bulb, even fingerprnts will cause it to burn out prematurely.

Jan 27, 2009 | 2003 BMW 5 Series

1 Answer

Replacement Bulbs


i believe on this car, low beams & fog lights use an HB4 and high beam uses an HB3. but, as bmw_tech_38 mentioned above, remove the old and it should be listed in the base.

Jan 22, 2009 | 1998 BMW Z3 Roadster

1 Answer

Changing headlamps on 2003 bmw 325xi


I am assuming that you have a burned out head light bulb.
1) Open hood.
2) Working in back of headlight assembly, grasp rear of bulb socket (harness connector) and turn counterclockwise 90 degrees. Pull bulb out of headlight assembly.
3) Disconnect harness connector from bulb (gently pry, it's plastic)
4) Installation is reverse of removal. (Do not touch halogen bulb with bare skin-oils from hand will cause bulb to burn out.) Align tabs on bulb base to cutouts on rear of lens assembly. (Note bottom tab is wider than other two) Secure bulb by rotating clockwise 90 degrees.
Low beam bulb H9006
High beam bulb H9005

Jan 07, 2009 | 2003 BMW 325

1 Answer

Burned out headlight/bulb bmw 1991 325i 2dr


It's a bulb replacement. If it's anything similar to my Audi, there is a cover on the back of the headlight housing that you pop off. Then you can reach in, pull the wire connector off the bulb, and unclip a metal retainer over the bulb, and pull the bulb out. Installation of the new one is the reverse. Just be SURE not to touch the glass part of the bulb. Skin oils can cause a halogen bulb to burn very hot and burn out very quickly. If you do touch the glass, wipe it gently but thoroughly on a cotton cloth to clean it off before you install it.

Oct 31, 2008 | 1991 BMW 3 Series

1 Answer

Low Beam Headlight


This is a bulb and is very easy to replace. You might want to buy a pair since other side will go out soon also. Simply twist connector behind light system, pull and replace bulb. good luck

Sep 08, 2008 | 2003 BMW 5 Series

Not finding what you are looking for?
2002 BMW 7 Series Logo

Related Topics:

758 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...