Question about 2000 Dodge Caravan

1 Answer

My radiator fan keeps running after shutoff, i need to know what is a headlamp module

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

An electric fan may run on after the engine is switched off to stop "hotspots"within the engine,but should switch off after,say,10/15 mins.dependant on outside temp and if you have just come off the highway.
a headlamp module is the whole headlamp lens,glass,fittings all in one unit rather than in bits....supposed to keep it weatherproof.....

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Headlight low beam on my envoy 2006 not working


The headlamp driver module (HDM) is an electronic module that provides electrical power to the vehicle low beam headlamps. The HDM is controlled by a pulse width modulated (PWM) ground signal from the body control module (BCM). The BCM determines the desired lamp intensity using the ambient light sensor, multifunction switch and the park brake switch as inputs. In general, the HDM will operate in 1 of 3 modes:
?€¢
Reduced Intensity Mode: This mode is used by features that do not require or allow maximum low beam headlamp intensity such as daytime running lights (DRL) (nominal: 85% duty cycle).


?€¢
Full Intensity Mode: This mode is used by features that require full low beam headlamp intensity such as low beam headlamp operation in manual or auto modes (nominal: 100% duty cycle).


?€¢
Off Mode: This is the default mode of the system that will occur when none of the features described above are active. The BCM will deactivate its PWM output (0% duty cycle) during this mode.

The normal battery voltage input to the HDM must be between 6 and 16 volts DC to operate. Any deviation to these values could cause improper operation.
Major components of this system are the BCM, HDM, ambient light sensor, multifunction switch, park brake switch and low beam headlamps.
DTC B2575 Headlamp Control Circuit
When the body control module (BCM) senses a request for headlamp or daytime running lamp (DRL) illumination, the BCM sends a pulse width modulated (PWM) ground signal to the low beam headlamp driver module through the low beam headlamp driver module control circuit. The low beam headlamp driver module will illuminate the headlamps, adjusting the intensity based on the PWM signal received
You best bet is to take your vehicle to a ASE certified repair shop or the dealer >

Jan 15, 2016 | GMC Envoy Cars & Trucks

1 Answer

Diagram of engine


The radiator cooling fan control module (also known as "radiator cooling fan relay", athough is is a solid-state control module - not a relay) is located on the left frame rail just behind the front bumper/headlamp area. You must to get under the vehicle and look up to see it. It looks like the picture below.
6_15_2012_12_08_06_pm.jpg

Jun 15, 2012 | 1996 Plymouth Voyager

2 Answers

Cooling fan keeps running after turning the car off.


You can unplug the fan so it doesnt run the battery dead. Typically what happens with these vehicles is that a failing radiator fan burns out the solid state fan relay, this can also cause the relay to short and supply continuous voltage to the fan assembly. The relay is located below the passenger headlamp but you will need to remove the front bumper to access it.

Feb 01, 2011 | 2002 Jeep Grand Cherokee

1 Answer

Where do I find the cooling fan relay switch on a 2000 dodge grand caravan sport.


RADIATOR FAN RELAY
The radiator fan relay is located below the left front headlamp module Radiator Fan Relay The headlamp module must be removed to access the relay.

REMOVAL
Open hood, disconnect and isolate the battery negative cable.
Remove the left side headlamp bulb from the headlamp housing.
Remove the left headlamp module.
Remove the cover over the relay.
Disconnect the relay connector Radiator Fan Relay
Carefully drill out the two retaining rivets.
Remove relay from vehicle.

Jul 15, 2010 | 2000 Dodge Caravan

1 Answer

Do you know where the radiator fan motor relay sensor would be?


The Pulse Width Modulated (PWM) cooling fan relay is located below the right headlamp behind the bumper fascia.

Nov 05, 2009 | 2000 Jeep Grand Cherokee

2 Answers

2002 Grand Cherokee Radiator Fan is staying on after i shut off vehicle. It is running down the battery.


common problem you have a bad cooling fan relay module. located behind right frt headlamp, hard to get to.hope this helps.

Oct 14, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Im looking for the location of the fan relay on my 2000 grand caravan with a 3.3 engine


The radiator fan relay is located below the left front headlamp module. The headlamp module must be removed to access the relay.

Jun 16, 2009 | 2000 Dodge Caravan

1 Answer

Int. fans keep running hours after eng. shutoff


the problem is not caused by the realy, it is caused by the fan speed control module, it is located near the fan motor on the passenger side under the dadsh behind the glove box, replace it.

Mar 20, 2009 | 1999 Buick LeSabre

2 Answers

The fan for the cooling system is not working and is brand new


There is a sensor on the radiator that controls a relay to turn the fan on. There is also a fuse in the fuse panel under the hood. Make sure the radiator is full.

Mar 13, 2009 | 2001 Jeep Grand Cherokee

1 Answer

HOW TO REPLACE HEADLIGHTS ON 2000 CHRYSLER LHS


ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Jul 28, 2008 | 1994 Chrysler New Yorker

Not finding what you are looking for?
2000 Dodge Caravan Logo

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...