Question about Chevrolet S 10

Open Question

Remove ignition switch 1984 chevy s10 - S 10 Chevrolet Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tripletauto
  • 1450 Answers

SOURCE: installing ignition switch for 87 chevy s10 Blazer 2.8L 4X4

you need to replace the electrical part of switch?If os it is down on column under dash will be two bolts holding on with the dimmer switch also

Posted on Aug 28, 2008

  • 1 Answer

SOURCE: I have a 97 Chevy S10 pickup...cannot move shifter out of park

When my battery was dead i was forcing the key in the ignition which messed everything up with my chevy s10 and have to get everything replaced....: (

Posted on Jan 20, 2009

MrScary66613
  • 1990 Answers

SOURCE: 1984 S10 wiper arms

No Problem! Look down on the Bottom of the Wiper Arm, wher it attaches and Swivels. There is a Small tab that comes off of the Upper Part of the Arm that looks like Two Front Teeth Sticking up just a Little. Take a Pair of Pliers and Pull this Tab Up Towards the Top of the Winshield to Release the Lock on the Arm. then take a Pair of Pliers with Tape on them so that you will not Scratch the Arm and Pull while you Wiggle the Arm right at the Swivel Pont and they will Come off. Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 28, 2009

  • 1596 Answers

SOURCE: ignition removal process for 1984 chevy 1/2 ton

This Outlines Removal Of Both LOCK CYLINDER<< Mechanical)) And The Ignition SWITCH ITSELF<< ELECTRICAL))

  1. Remove steering wheel as outlined previously.
  2. Remove turn signal switch as outlined in ``Turn Signal Switch, Replace'' procedure.
  3. Place ignition switch in ``Run'' position, then remove lock cylinder retaining screw and lock cylinder.
  4. To install, rotate lock cylinder to stop, while holding housing as shown, Fig. 6. Align cylinder key with keyway in housing, then push lock cylinder assembly into housing until fully seated.
  5. Install lock cylinder retaining screw. Torque screw to 40 inch lbs. for standard columns, or 22 inch lbs. for adjustable columns.
  6. Install buzzer switch, turn signal switch and steering wheel


CABALLERO, EL CAMINO, C, K, R, V & 1986---87 G MODELS
The ignition switch is mounted on top of the mast jacket inside the brake pedal support and is actuated by a rod and rack assembly.
  1. Disconnect battery ground cable.
  2. Disconnect and lower steering column. On some models, it may be necessary to remove the upper column mounting bracket if it hinders servicing of switch. Use extreme care when lowering steering column to prevent damage to column assembly. Only lower steering column a sufficient distance to perform ignition switch service.
  3. On Caballero and El Camino, rotate ignition lock to ``Off'' unlocked position.
  4. On C, K, R and V models, rotate ignition lock to ``Off'' locked position.
  5. If lock cylinder has been removed, pull switch actuator rod up to stop, then pushrod down to second (Caballero or El Camino) or first (C, K, R and V models) detent as shown, Fig. 7.
  6. Remove column mounted dimmer switch, if equipped, then remove switch retaining screws and switch.
  7. Reverse procedure to install, noting the following:
    1. Place gear shift lever in neutral.
    2. Place lock cylinder and switch in positions noted in steps 3 and 4.
    3. Fit actuator rod into hole in switch slider and secure switch with retaining screws, ensuring switch does not move out of detent.
    4. Install and adjust dimmer switch, if equipped, as outlined in ``Column Mounted Dimmer Switch, Replace'' procedure.
    5. Torque retaining screws to 35 inch lbs., then check switch operation.

Posted on Feb 21, 2009

  • 407 Answers

SOURCE: removal of 1976 chevy truck ignition switch

need a special tool to remove the locking plate behind steering wheel then pull turn signal switch back a little then remove screw that keeps lock cylinder in place

Posted on Oct 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1984 chevy s10 and the high beams will not work any ideas


If the bulbs and connectors are good, then i'd say replace the switch

Jun 06, 2012 | 1984 Chevrolet S-10

1 Answer

I need the wiring layout for an 1984 chevy s-10 ignition module


Got an 84 shop manual with wiring

What do you need ?

Also got a 1984 S10 Blazer since new

Oct 08, 2010 | 1984 Chevrolet S-10

1 Answer

I dont know how to replace a fuel filter on my 1984 chevy s10 can you help me out


1984 Chevrolet Truck S10 P/U 4WD 2.8L 2BL 6cyl the Fuel Filter is located under hood, center, upper engine area, front of carburetor, mounted in fuel line.

First, release the fuel pressure by opening the fuel filler door. Then you replace it by squeezing the quick release plastic clip on the front and sliding the fuel line forward; you then use a wrench to loosen the nut on the back. Be prepared for some gas spillage with a container or some old rags. Once it is loosened, you remove it from its bracket, replace it, hook it back up (reverse of what you did) and it should be good to go.

Good luck.

May 19, 2010 | 1984 Chevrolet Chevy

1 Answer

How to change a torque converter seal on a 1984 chevy s10 4wd pickup


remove the transmission,remove the converter,and use a screw driver,and pry the seal out,then just tap the new seal in with a block of wood.

Apr 08, 2010 | 1984 Chevrolet Chevy

1 Answer

1984 chevy s10


some of these cars had a low pressure fuel cut off switch buit into the oil pressure switch, make sure you have the correct oil sending unit. hope this helps let me know. ps use a a/cdelco part

Apr 10, 2009 | 1984 Chevrolet S-10

1 Answer

84 chevy S10


sounds like u may have a bad ignition coil or pick up modual

Feb 11, 2009 | 1984 Chevrolet S-10

1 Answer

1984 chevy S10 windshild wipers


at the arm remove the cap on end and their is a nut remove it 10 mm / Please rate my response thank you very much

Jan 28, 2009 | 1984 Chevrolet S-10

1 Answer

1984 S10 head lights


The switch could be out. Under the dash their will be a pannel that covers the stering wheel shaft remove this. On the top of the shaft their will be two bars that go down to a box, one is for the ignition the other is the high beams. Replace the box that the light switch goes to. This should fix ya.

Please contact me if your problem presist.

Thanks, Charlie

Jan 27, 2009 | 1985 Chevrolet Chevy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...