Question about Hyundai Tiburon

1 Answer

I have a 2000 tiburon that need the rear ball joint replaced. i keep having problems finding the part. is the ball joint on a larger part i have to buy? ho do i rplace this?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 662 Answers

This is a a link to an example of the rear ball joint

http://www.partsgeek.com/catalog/2000/hyundai/tiburon/suspension/ball_joint.html

... this bushing actually mounts in the rear hub carrier and connects to the upper control arm

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 mazda mpv passenger side ball bearing location


The following items on your Mazda have ball bearings, and are on the passenger side.
1) Wheel bearings, front and rear.
2) CV joints, inner and outer.
3) Alternator, front and rear.
4) Power steering pump.
5) Water pump.
6) Idler pulley and/or tensioner pulley.
7) A.C. Compressor.
8) a few I may have missed.

Oct 29, 2015 | 2000 Mazda MPV

1 Answer

I have a 2000 k3500 7.4 bad lower ball joint .Do i have to take the lower control arm off or can i replace it on the truck.? thanks.


YOU REPLACE BALL JOINT IN TRUCK BUT YOU NEED BALL JOINT TOOL J 9519 - 30- D TO PRESS BALL JOINT OUT OF THE LOWER CONTROL ARM.

Sep 20, 2011 | Chevrolet K3500 Cars & Trucks

2 Answers

PROBLEMS with drive shaft thi is the 3rd time i have to rebuild the drive shaft is a 2 part drive shaft 1time rebuild the front part and 2 times the rear part any advise why is this happening


The only thing that should kill the shaft that many times is having it out of balance. Eventually a two-piece shaft will fail but it's usually after a couple hundred thousand miles. To have three of them fail seems to suggest that when they've been rebuilt, they haven't been balanced properly afterward. Find a truckstop and have their service guys rebuild it if there's no dedicated driveshaft shop near you. Truck guys will have the knowledge and equipment to properly reassemble and balance the shaft.

Dec 03, 2009 | 2002 Chevrolet S-10

1 Answer

Ball joint wont go back on


Ha ha yeah Put a jack under bottom arm to put pressure onto balljoint taper

Jul 09, 2009 | 1998 Hyundai Tiburon

1 Answer

REPLACING LOWER BALL JOINTS ON 2000 FORD F250 4X4 7.3L DIESEL


hello,yes you do have to take the hub off to replace the ball joint with the ball joint being on the back side of the hub. hope this helps and please rate this.

Mar 15, 2009 | 2000 Ford F250 Super Duty Crew Cabs

4 Answers

CLUNKING NOISE FROM REAR AXLE


Problem I found: Clunk when driving over even small bumps.

If Grand Cherokee is 1999-2004, then check this: Above the differential is a wishbone cross member control arm. The cross member attaches to the frame in front of the rear axle (bolts through rubber bushings), and directly above the differential, at the apex of the cross member, is a ball joint. The ball joint assembly is a flange bolted atop the differential, with three bolts, and the ball joint pin protrudes from the flange through the cross member apex, with a nut atop the pin. Raise the frame slightly, and with a pry bar, pry above the flange, and below the cross member, very near the ball joint. If any motion is detected, then the ball joint is worn from the ball joint socket, or the nut is loose on the ball joint pin. If the nut is tight, then replace the ball joint. 2000 GC part number is 52088808AB, and is available from online sources or dealers. To replace this part, you'll probably need to remove the cross member, as the ball joint pin through the cross member is in a tight location, is tightly wedged into the cross member, and requires a special v-shaped puller to remove the pin from the cross member. If you don't have access to the puller tool, then remove the cross member for this operation. Raise vehicle slightly, under frame, in front of rear wheels. Unbolt the brake line and brake cable retainers from the cross member, then unbolt the flange from atop the differential. Then remove the two frame bolts and manipulate the cross member out of the vehicle, from above the differential.

With the cross member before you, support on blocks, loosen the ball joint nut somewhat, or remove it, and with a beater protective block, sledge out the pin from the cross member. Inspect the rubber bushings at this time. These bushings require an arbor press to remove/install, and the arbor press to install requires a spider so as to not rip the rubber bushing from either the bushing shell or center spool. The press spider is a 4-point tool you can make up from a piece of aluminum.

Bolt the new ball joint flange atop the differential, using blue thread locker, and torque the bolts to 100 ft-lb, cheater pipe useful here.

Replace the cross member to the frame, and install the two frame bolts, finger tight. Pull the member apex down onto the ball joint pin, and run the nut down. Using a box end wrench, hold the pin from rotation while tightening down the nut. Torque the nut to 100 ft-lb. Tighten the frame attachment bolts to 100 ft-lb, and reinstall the brake cable and brake line retainers. Do not over tighten these retainer bolts, as they are passing only through the sheet steel side of the cross member. Take care to not strip the sheet metal threadings. Lower vehicle and remove jack.

May 15, 2008 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...