Question about 1998 Chrysler Town & Country

1 Answer

My hub is having problems with rust on the van doors and the undersides. He's been told by three different repair guys that this van really wasn't made for cold weather states.Is this a common problem?Has anyone else had this problem? Other than that, he loves his van!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,033 Answers

Any car that is around cold weather is really not the problem, it's the salt and sand that they put on roads during ice storms. This stuff will eat a car up. It's the same way around real salty beaches. Not saying cold isn't a factor but these others are the worst factors.

Posted on Aug 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Repair Van sliding door runner


If the Pontiac Trans Sport Van door is in the process of closing or opening (via motor), and the vehicle's ignition is engaged prior to the door fully closing or opening, the motor immediately stops. At this point, the only recourse is to manually close the door, as none of the power switches/handles respond again until the door has been manually closed. ----------------------------------------------------------------------------------
Car cable & OBD Connector

Dec 12, 2012 | Mitsubishi Cars & Trucks

2 Answers

How remove the rotor to change bearing for 2005 chev colorado front


first you remove all the lug nuts and the wheel and tire. To get the rotor off you will need to remove the brake caliper. they are held in with 1/4" hex screws. If you don't have an allen wrench you can use a socket extension to removes these. Once unscrewed the calpet simply lifts off the rotor and the rotor is ready to come off. You will need to remove the axle nut and keeper then the rotor slides off towards you and the wheel bearings will come out with the rotor.

Sep 26, 2011 | 2005 Chevrolet Colorado

2 Answers

I have a 2001 aztek. ABS light comes on. But my biggest problem seems to be that my car jerks like it is the transmission slipping. My husband had it looked at and was told it is the speed control censor....


Get Another Car--LOL

Really --just throw that one away

Can you afford to do that?

When it was looked at ,why didn't you have it repaired?

The ABS Light is on -- so why wasn't that issue
diagnosed & repaired. That may be a Wheel Speed Sensor

Not the same thing as a transmission output speed sensor

I think vehicle technology is beyond your learning curve, at the
moment
Find a half decent repair shop

Jul 12, 2011 | 2004 Pontiac Aztek

3 Answers

A guy driving behind me this morning told me that my left brake light was flickering. Is there some way I can check to see if it is loose or is there instructions on how to change the bulb myself?


Not knowing the year of the truck makes a difference. However if you go to the light in question you shoulds see three or four screws holding the light to the truck. remove the screws and then on the back of the housing you will see a couple of plugs remove the plug and check the bulb. Look at it and see if the little wire is intact. if not replace and reinstall.

Apr 20, 2011 | GMC Yukon XL Cars & Trucks

1 Answer

My door lights stays on suspect the censors where are they located


If you are not getting a dinging noise I would suggest you get a fine grit sand paper.Open your sliding side door and sand down the the silver connections on the door and on the body of the van.You have to really put some pressure on it.Do it for a few minutes.Wipe them off and close the door.See if that solves the problem.I have read on many sites that this doesnt fix it.I have the same van and had the same problem.I did this and the lights go out,the door adjar light is off and I dont have any idiot lights flashing on the dash.it has been like this for three months now.

Oct 07, 2010 | 1998 Ford Windstar

1 Answer

I own a kia optima 2003 My car died while I was driving down the road. We thought it was the coil come to find out it wasn't. We then took the cover off the timing belt and notice the some teeth where...


Firstly don't ever wish you was a guy because that wouldn't automatically make you understand cars, though it might make you mistakenly think you understand them. When females enter traditional male preserves and train to become plumbers, electricians, engineers or motor mechanics they mostly become very good and show the guys a thing or three...

Clearly the very first thing is to replace the timing belt. Fortunately lots of timing belt kits arrive with instructions and illustrations these days so there are few problems with timing.

Once fitted you will be able to attempt to start the engine but be aware if the timing did jump a few teeth some damage to the engine intake and exhaust valves might have occurred and if you are really unlucky the damage could be substantial. If the engine won't start and run I suggest you have a compression test or even better a cylinder leakage test.

When you hired the machine it might have told you useful information or it might have been misleading lies. Certainly it would be a good idea to look at No1 spark plug and maybe test the crank sensor but it is best to proceed slowly and tackle one job at a time because one type of fault tends to cause symptoms that cause the computer to believe there is a different sort of fault.

Lots of guys spend lots of money unnecessarily by believing what diagnostic machines tell them instead of using those results as part of a systematic diagnostic process.

Good luck!

May 07, 2017 | Kia Optima Cars & Trucks

1 Answer

Rust behind both front door (top only) hinges


If there is rust, the bolts are loose and the hinge is working (moving) causing bare metal exposure to rusting. Tighten the bolts, iit will be ok.

Jun 02, 2009 | 1993 Cadillac DeVille

2 Answers

Olds Alero 99 Left front hub assembly


I found on some of the GM hubs it actually wasn;t the hub at all but a broken wire in the spped sensor harness about 8" back into the harness fixed the wire problem fixed.

Aug 21, 2008 | 2003 Oldsmobile Alero

Not finding what you are looking for?
1998 Chrysler Town & Country Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...