Question about 2004 Dodge Durango

1 Answer

How do i remove a rear wheel stud on a 04 dodge durango

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 172 Answers

I think these are pressed in to the plate, you will need to get an axle puller, pull the half-shaft out, and take it to a machine shop. They can press the old stud out and press the new one in.

Posted on Aug 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Broken wheel stud right rear wheel with drum brakes on 2006 dodge caravan. Cant get the new stud to go in. I dont have enough room for the stud to go in. Do i need to remove the wheel bearing? What will be...


To remove the broken stud use a punch and drive it out with a hammer back towards the backing plate. BY turning the axle around you will find a position or you may have to remove a brake shoe to help with the installation of the new stud. When you have it in place use larger nuts and pull it into place with the stud nut.. You may not be able to simply put the stud straight in but may have to start a bit of an angle and turn the axle to allow the stud to feed in.

Sep 01, 2013 | 2006 Dodge Grand Caravan

1 Answer

To replace rear wheel studs in a 04 durango, does the axle have to be removed?


No the axle doesn't need to be removed, but it makes it easier.

Dec 15, 2011 | 2004 Dodge Durango

1 Answer

How to get drum pads off a 2000 dodge caravan


The pad drums of your 2000 Dodge Grand Caravan can wear with use. Heat buildup in the brakes can glaze, warp or crack the drum. If that happens, replacement of the drum is the only way to fix it. In most cases, you can remove the rear drums, replace them with a new set and leave the existing shoes on the van. Take a minute and inspect the brake shoes thoroughly while you have the drums off the van.


  1. Loosen the lug nuts on the rear of your 2000 Dodge Grand Caravan with a lug wrench. Do not take them off the wheel studs.
  2. Raise the rear of the van with a jack and support it on a set of jack stands. Place the stands under the rear suspension, making sure they are secure. Remove the lug nuts from the wheel studs and pull off the rear wheels.
  3. Check the rear drum where the wheel studs come through for retaining clips. These are used during the manufacturing process; and if they are still on your van, they need to be removed. Pry the clip off the wheel stud with a flat head screwdriver and discard them. Most vehicles will have two clips on each brake drum.
  4. Grasp the brake drum on the outer edges and pull it straight off the wheel studs and brake pads. Discard the old drum and slide the new drum into place, aligning the holes in the drum with the wheel studs. Push the drum in until it seats completely. Repeat the process on the opposite side of the van.
  5. Position the wheel back on the wheel studs and install the lug nuts by hand. Raise the back of the van with a jack and remove the jack stands from under the suspension. Lower the van to the ground and tighten the lug nuts with a lug wrench.

Jan 08, 2011 | 2000 Dodge Caravan

2 Answers

Where is the jack and tools for spare tire?


CHANGING A FLAT TIRE
Jack Location
In the Durango, the scissor jack and tire changing tools
are stowed under the second row seat.
The jack is secured in place with a winged stud and a
fixed stud. It is very important to secure the jack tightly
in place by engaging the slot in the base to the fixed stud
under the middle seat. The winged stud inserts through
the eyelet in the end of the jack’s worm screw.

Dec 09, 2009 | 2001 Dodge Durango

2 Answers

How to replace rear wheel stud. 2003 dodge caravan


Should be a pressed in wheel stud, remove hub and have old one pressed out or you can do it the primitive way, by double nutting the old stud and striking it with a hammer to pound it out, if threads are bad then just strike the stud by itself , then replace new stud in opposite fashion...

Sep 15, 2009 | 2003 Dodge Caravan

1 Answer

How to remove rear seat in 1996 dodge ram 1500


REMOVAL & INSTALLATION
  1. Clamp the seat belts to keep them from retracting.
  2. Locate and disconnect seat wiring at the connector(s).
  3. Move front seats forward or back for access to the hold down hardware.
  4. Put the rear seats in the stowed position.
  5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
  6. Remove the hardware securing the seat.
  7. On split bench models, lift the center seat upward to clear attachment stud
  8. Remove the seat from the vehicle.
NOTE Do NOT activate the track adjusters once the fastening hardware is removed.
  1. Installation is the reverse of removal.

336abe0.gif


Fig. Disconnect the wiring from under the seat

36c62e2.gif


Fig. Seat track mounting hardware locations-typical


d95c538.gif

Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram


1589e1e.gif

Fig. Split bench seat assembly-Ram


616f086.gif

Fig. Bucket seat mounting components-Durango shown


851105e.gif

Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

Aug 31, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

How do i get at, and change the rear wheel bearing in my 1999 dodge durango


Wheel bearing should be permant packed. However if you wish to tackle the job. Remove the wheel, remove the cap, remove the carter pin, remove the bearings. Clean, repack new bearings and reasemble. But, before you do check with any auto repair shop or Dodge dealer, bearings may be permantly sealed.

Jun 10, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
2004 Dodge Durango Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...