Question about 2002 Chevrolet TrailBlazer

1 Answer

Front right side turn signal/running is out. How can I remove the light socket once I raise the hood?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,311 Answers

First remove the grille assembly, there are eight clips holding the grille. Start at the top and gently pry the grille toward you. Once grille is off, find two L-shaped tabs just above the headlight assemblies, pull these straight up to release the assembly. At this point you will access to all of the bulbs.

Posted on Oct 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change front turn signal


The side marker light must be removed in order to get at the turn signal light.
There are two screws holding the side marker light which is situated above the turn signal.
Open the hood.
Remove the phillips head screw at the top of the side marker light.
Using a long #2 Phillips screwdriver, remove the screw on the outside of the side marker light. This can be seen by looking between the lower side of the side marker light and the top side of the turn signal.
The side marker can be moved.
The turn signal has one screw on the top of the fixture that must be removed.
Slide out the turn signal fixture. There is a small feature on the lower front corner of the turn signal fixture that you must note to properly reinstall the turn signal.
In order to get to the bulb, rotate the bulb socket 1/4 turn CW or CCW. The bulb socket is loose.
The bulb is simply pressed into the socket.
Not sure of the type, but it can be found at your locale auto parts store.
The bulb is used in several places on the 1994 GC, so get apacket with two, if possible.
Assembly in reverse. Be careful not to overtighten the screws as they are replaced.

Mar 29, 2011 | 1994 Jeep Grand Cherokee

1 Answer

The right front turn signal on 2005 chev uplander works and then stops and then starts then the left rear stopped working and now the fan doesn't work, why???


I just replaced all the signal lights on my 2005 van. You may have a cracked and or loose filiments that may be making intermittent conact in your bulbs. I would recommend replacing both your front and rear signal lights to start with and see if that clears up your problem. I aleady have a full procedure written up and will past it below, please use what you need. Note, our vehicles need to have the headlights out to reach the front turn signals below them. My proceedure discripbes how... Hope this helps.

Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, place the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)

Jan 11, 2011 | 2005 Chevrolet Uplander

1 Answer

Trying to change a front right head light


I have put together a general doucment covering the exterior lights for the Uplander. I have also included the bulb types. It will take some disassembly to reach the lights>>>>

Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, please the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)


Dec 29, 2010 | 2005 Chevrolet Uplander

1 Answer

How to change front headlight passenger side 2006 uplander and turn signal


I have written up a proceedure for my 2005. I would think it would work for a 2006. At the end is a light bulb list...

Your owners manual also gives a good discription on how to remove the head lights as well.

Todd


Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, place the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)

Dec 19, 2010 | 2006 Chevrolet Uplander

1 Answer

How do you change front turn signal bulb


I have written a procedure for all the lamps plus a lamp list. Hope this helps you....

Todd

Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, place the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)

Dec 18, 2010 | 2006 Chevrolet Uplander

1 Answer

Need to replace front turn signal bulb


I have written up a proceedure for my 2005. It should still work for a 2007. I also have a bulb list at the end. Your owners manual also gives a good discription on how to remove the head light. Unfortunally, the head light assembley has to be pulled out to reach the back side of the front turn signal. Hope this helps...

Todd.

Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, place the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)

Dec 03, 2010 | 2007 Chevrolet Uplander

1 Answer

Front turn signal replacing bulb


Chevy Uplander Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


To gain access to the turn signal, the headlight assembly needs to be moved out of the way so you can reach under to the rear of the turn signal. Below is a cut and past from my how to lights document for this. You can pull from this what you need to remove the headlight assemby. Bulb types are also listed at the end. I hope this helps>>


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There is no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise (clock wise on drivers side) and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fare amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, please the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)


Nov 22, 2010 | 2005 Chevrolet Uplander

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

2 Answers

How do I replace the turn signal bulb on my 1997 Jeep Grand Cherokee? It seems like I must remove alot of the front end to get at the bulb... is this true?


For the front turn signal:

There are two ways to get at the bulb.

Way 1) YOU NEED A SKINNY SHAFTED STAR SCREWDRIVER. This is how the manual describes it: Unscrew the 2 star screws holding the parking light housing on. One is on top, the other is between the parking light and the turn signal. This second screw can be very difficult to get to because the parking light and turn signal housing are very close. After the parking light housing is off, you can unscrew the turn signal housing. The screws should be located on top of the housing, underneath the parking light housing.

Way 2) This is the way I did mine: First, you have to take the headlight housing off. It should be pretty easy to pop off if you pry it the right way. It is held on by 1 square clip and 2 ball and socket clips. There is a small risk of breaking the ball and socket clips, as getting the headlamp housing off does require a little force, so be careful. You may want to take the headlight bulb out first, but isn't necessary. (Removing the right side bulb may require removing the battery) Once the headlamp housing is off, the turn signal bulbs should be very easy to get to.

To remove the bulb, simply turn the bulb socket and it will come out.


For the rear turn signal:


Open the lift gate.

There are 3 hex screws that hold each rear light assembly on. I'd recommend a hex screwdriver, as a socket wrench or box wrench would be very hard to use on the screws. Once the hex screws are off, just tug on the light assembly and it will come off. The bulbs are very easy to get to. The turn signal is the yellow one.

Nov 10, 2009 | 1997 Jeep Grand Cherokee

1 Answer

How do I replace the headlight assembly on a 2006 sebring?


  1. Remove the front bumper cover
  2. Remove the upper headlight housing mounting bolt and pushpin
  3. Remove the lower headlight housing mounting bolts
  4. Pull out the headlight housing assembly and disconnect the electrical connector.
Its pretty easy. Just raise the hood, see the two silver 8mm cap screws on top of the cross member that supports the radiator and fan assembly. Two screws on each side above the headlight housings. The outer screw is right next to the corner of the fender when the hood is raised. Remove the two screws, then the headlight assembly is loose. Just gently pull the headlight assembly forward enought to see the three lamp socket holders on the back side of the headlight assembly. From the outside corner to the inside are first, the parking turn signal, then the low beam lamp and finally the last, the high beam lamp. To remove the lamp socket, push the small plastic locking tab and turn the socket assemby counter clockwise about a half turn and remove the lamp. Now you can replace the lamp and install it back the same way you took it out. Don't touch the new lamp glass with your bare fingers. Oil from you skin will absorb into the glass causing the glass to turn dark and shorten the lamp life. 

May 04, 2009 | 2006 Chrysler Sebring

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...