Question about Toyota Camry

1 Answer

It is too hard to turn the wheel in all speeds

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

It is a Toyota
replace the rack and pinion

Posted on Aug 28, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Anti-lock function on brakes is triggered by applying brakes while steering wheel is turned hard over


Sounds like you are losing wheel speed signal when under hard turns. This is commonly caused by the harness at or near the wheel speed sensor has a bad connection of there may be a break in the wiring that intermittently loses signal to the ABS module and causes the anti-lock function to happen, (loss of wheel speed is like wheel skid as far as the ABS module is concerned) It is usually necessary to have a scan tool to monitor the data and read codes on the ABS system. You may have to take vehicle to shop that is capable of diagnosing the problem.

Oct 13, 2015 | 2003 GMC Sierra 1500

2 Answers

What causes my 2-wheel drive ranger to vibrate hard when I turn the steering wheel at low speeds only, like pulling out of garage? also does it in reverse. makes a noise near the rear when it is vibra


i would say it is a solenoid or air in the power steering lines but you would have to put a obd2 scanner and see what it says.
if i remember correct bleeding is as simple as removing the power steering cap and turning steering all the way left hold for 5 seconds then right and hold but you will need to look at oil in reservoir and see if it is bubbling while turning and holding. you will need a helper and if it is do this for 5-10 minutes.

Oct 10, 2014 | 2000 Ford Ranger SuperCab

1 Answer

What is a vdc light


Vehicle Dynamic Control, measures inputs from different sensors ie: wheel speed from ABS wheel sensors, trans gear position & speed, Yaw rate, throttle position, etc then makes determination on how to best control veh in a certain situation (accelerating to hard through a turn, wheel spin on wet pavement, sliding during hard stops and such). Can do one or a combination of commands to recover an out of control veh like release brake psi to locked wheel (ABS), limit accelerator, down shift trans, even transfer shift power from side to side/frt to back on some models.

Sep 03, 2014 | 2011 Nissan Pathfinder 4.0

2 Answers

Why does my traction contol turn on when i make a hard left turn?


Your traction control looks at a difference in wheel speeds and kicks in when a set wheel speed difference is seen. The system is just doing its job

May 06, 2014 | 2008 Dodge Grand Caravan

1 Answer

Clattering from front tires when turning at low speeds


Depending on how hard or sharp you are turning, this could be the CV joints.

Sep 25, 2012 | Audi A6 Cars & Trucks

1 Answer

Shakes, steering wheel hard to turn. RPM's at 2 when going 15mph.


Have you checked the power steering fluid? Do the belts squeel when you turn the steering wheel?
I know this might sound silly but are your air pressures in your tyres correct? Low air pressure will cause your steering to shake at speed and it will be hard to turn at low speed.
I hope this helps,
Scott.

Apr 25, 2011 | Dodge Durango Cars & Trucks

1 Answer

Steering not straightening out at slow speed


Worn steering components which allow the steering wheels to travel too far either way,hop underneath and get a friend to move the steering while you have a look for movement between the components, or a power steering component like relief valve. Its a bit hard to know without seeing the vehicle, i suggest a steering and suspension specialist like pedders or similar.These guys can do a safety inspection only, if you want to do the work yourself. Cheers Timo.

Apr 27, 2010 | 2004 Ford Explorer

1 Answer

Hard low speed turns


Crawl under the truck and look at the steering linkage. You may have to have someone turn the steering wheel while under. Do not crawl under without supporting the vehicle and placing chocks in front of the wheels. While someone turns the wheel look for binding where there are moving parts. Look at your tie rods and steering arm. Does it turn hard in one direction only? If so look at the side your turning into. Is this a four wheel drive? You may be in four wheel drive? Low speed turns with four wheel drive can cause torquing on dry pavement.

Dec 01, 2009 | 1998 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...