Question about 1999 Cadillac DeVille

1 Answer

No electrical current to ignition coil for spark plug 8 & 3

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,190 Answers

If 3-8 coil is not getting 12v(remove coil connect a test light to terminls sticking up from the module turn engine over with starter test light should blink) if light doesn't blink replaCE THE IGNITION MODULE

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a coil pack on a Chevy Tahoe


To Remove......
1. Remove the spark plug wire from the ignition coil.
2. Disconnect the ignition coil electrical connector.
3. Remove ignition coil bolts.
4. Remove ignition coil.

To Install.....
1. Install ignition coil.
2. Install ignition coil bolts.
3. Tighten ignition coil bolts to 8 Nm the same as 71 inch pounds.
4. Connect ignition coil electrical connector.
5. And finally, install spark plug wire to ignition coil.

Apr 22, 2015 | Chevrolet Tahoe Cars & Trucks

1 Answer

Spark plugs


Check this SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

How to change spark plugs in a 2005 chev colorado


SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

2 Answers

How do I replace the ignition coil in my 2002 ford taurus



Removal & Installation

3.0L (VIN S) Engine

  1. Disconnect the negative battery cable.
  2. Unplug the engine control sensor wiring connectors from the ignition coil and the radio ignition interference capacitor.
  3. Tag and disconnect the spark plug wires from the coil by squeezing the locking tabs, then twist the tab and pull upwards.
  4. Unfasten the four ignition coil retainers and remove the coil and the coil ground wire the radio ignition interference capacitor. Save the capacitor and coil ground wire for re-installation of the coil assembly.
  5. Wipe the coil towers with a clean cloth dampened with soap and water. Remove any soap film and dry with compressed air. Inspect the coil for cracks, carbon tracking, dirt or damage and replace as necessary.

    0996b43f802333d8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Ignition coil assembly mounting-3.0L DOHC engines


To install:
  1. Place the coil, capacitor and the coil ground wire onto its mounting location on the right hand valve cover.
  2. Install the coil assembly retainers and tighten to 45-61 inch lbs. (5-7 Nm)..
  3. Apply dielectric compound D7AZ-19A331-A or its equivalent to the spark plug wire boots.
  4. Attach the spark plug wires to their proper terminals on the coil and make sure the boots are firmly seated so that the locking tabs engage.
  5. Attach the engine control wiring connectors to the ignition coil and the radio ignition interference capacitor.
  6. Connect the negative battery cable, start the vehicle and check for proper operation.

Dec 19, 2010 | 2002 Ford Taurus

1 Answer

I am looking for a spark plug wiring diagram for 1997 buick park ave 3.8 to see if the wires may be crossed.


Sometimes the coil packs are numbered from the factory --- Firing Order 1-6-5-4-3-2
Ignition Coil Removal & Installation To Remove:
Ignition Coils gm-02-38-1037.gif

  1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
  2. Disconnect the spark plug wires from the coils
  3. Remove the fasteners securing the coil(s)
  4. Remove the coil(s) from the ignition control module
To Install:
  1. Install the coil(s) to the ignition module
  2. Install the coil fasteners
    • Torque to 40 in-lbs (4.5 Nm)
  3. Connect the spark plug wires to coil assemblies
---
Ignition Module Removal & Installation To Remove:
Ignition Coils gm-02-38-1037.gif

  1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
  2. Turn the ignition OFF
  3. Disconnect the 14-way connector from the ignition module
  4. Note the position of the spark plug wires and disconnect from the coils
  5. Remove the fasteners securing the coil(s)
  6. Remove the coils and the Ignition module from the bracket
To Install:
  1. Install the coils and the ignition module to the bracket
  2. Install the fasteners that retain the ignition coils to the ignition module
    • Torque the fasteners to 40 in-lbs (4.5 Nm)
  3. Install the nuts and washers that retain the ignition module to the bracket
    • Torque the screws to 70 in-lbs (8 Nm)
  4. Connect the spark plug wires to the coils assemblies
  5. Connect the 14-way connector to the ignition module
    • Torque the screw to 19 in-lbs (2.1 Nm)
prev.gif next.gif

Oct 26, 2010 | 1997 Buick Park Avenue

1 Answer

Where would the pvc value be on a 300 chrysler 2006? also where would the spark plugs be located?


Positive Crankcase Ventilation (PVC) Valve Removal & Installation 5.7L Engine To Remove:
    1.The PCV valve is mounted into the top/right side of the intake manifold.

    2.The PCV valve is sealed to the intake manifold with two O-rings.

    3.Free the PCV valve by rotating counter-clockwise 90 degrees until the locating tabs align with the openings on the manifold.

    4.Remove the PCV valve by pulling straight up from intake manifold and clearing the tabs.

    5.Check the condition of two valve O-rings.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Inspect the PCV valve O-rings. Replace if suspect.
  3. Apply engine oil to the two O-rings.
  4. Place the PCV valve into intake manifold.
  5. Rotate the valve 90 degrees clockwise for installation.
6.1L Engine To Remove:
  1. The PCV valve is threaded into the right-front corner of the intake manifold.
  2. Remove the rubber hose from the PCV valve.
  3. Unscrew the PCV valve from the intake manifold.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Check the condition of the PCV valve O-ring. Replace if suspect.
  3. Check the condition of the PCV valve threads and clean if necessary.
  4. Apply engine oil to the O-ring.
  5. Install the PCV valve into intake manifold.
  6. Install the rubber hose to the PCV valve.
prev.gif next.gif
The spark plugs should lead to the coil pack via a spark plug wire but may be hidden by a plastic cover.

The following details the ignition coil changing on the Chrysler 300:

2.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
  1. Install the ignition coil.
  2. Tighten the fasteners to 55 in-lb (6.2 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
3.5L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil. NOTE: Loosen the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when loosening the fasteners.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
NOTE: Tighten the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when installing the coil.
  1. Install the ignition coil.
  2. Tighten the fasteners to 60 in-lb (6.7 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
5.7L Engine (2005) To Remove:
NOTE: Carefully note the position of each spark plug cable before disconnecting them so they can be installed in their original positions to prevent misfire.
NOTE: The throttle body intake air duct or intake air box may need to be removed to gain access to certain ignition coils.
  1. Disconnect the electrical connector from the ignition coil.
  2. Remove the secondary ignition cable from the coil.
  3. Use compressed air to clear the area around the ignition coil.
  4. Remove the two fasteners securing the ignition coil. Bolts are retained to coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Clean area around spark plug and coil mounting area with compressed air.
  2. Install the ignition coil.
  3. Tighten the fasteners to 105 in-lb (12 Nm).
  4. Connect the electrical connector to the ignition coil.
  5. Connect the secondary ignition cable to the coil.
  6. Install the air duct or air box if removed.
Ignition coil mounting bolts (5.7L & 6.1L engines) chry-02-57-263.gif

5.7L (2006) & 6.1L Engine To Remove:
NOTE: Each ignition coil, mounted on the valve cover, fires two spark plugs at each cylinder.
  1. Disconnect the negative battery cable.
  2. Use compressed air to clear the area around the ignition coil and spark plug.
  3. Disconnect the electrical connector from the ignition coil.
  4. Remove the two fasteners securing the ignition coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Install the ignition coil.
  2. Tighten the fasteners to 105 in-lb (12 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Connect the negative battery cable.
prev.gif next.gif

Sep 24, 2010 | 2005 Chrysler 300

1 Answer

There is a misfire in my engine, changed plugs & wires. now it reads that the fuel leveling sensor is bad, will this help?


If there is a misfire, the cylinder that it is misfiring in will be recorded as a code in the computer.

Have the car scanned to determine which cylinder is bad. Then, replace the coil pack going to that cylinder.

Ignition Coil Pack Removal & Installation 2V Engine To Remove:
  1. Twist the spark plug wires off of the ignition coil towers. Mark the spark plug wire positions so they can be installed in their original positions.
  2. Disconnect the electrical connector from the ignition coil. CAUTION
    When removing the spark plug wires, a slight twisting motion will break the seal and ease removal.
    coilconn.gif

  3. Remove the mounting screws and remove the ignition coil.
To Install:
  1. Position the ignition coil pack on engine.
  2. Install mounting screws and torque to 53 in-lbs. (6 Nm). coilbolt.gif

  3. Connect ignition coil pack electrical connector.
  4. Match previously marked spark plug wires to ignition coil and install.
4V Engine To Remove:
  1. Remove the RH cowl grille cowlpic.gif
  2. Remove the screws and the water shield
  3. Mark spark plug wire positions
  4. Disconnect the spark plug wires from the ignition coil CAUTION
    When removing the spark plug wires a slight twisting motion will break the seal and ease removal.
  5. Disconnect the ignition coil electrical connector coilconn.gif

  6. Remove the mounting screws and remove the ignition coil
To Install:
  1. Position ignition coil pack. Install mounting screws and torque to 56 in-lbs. (6Nm)
    coilbolt.gif

  2. Connect ignition coil pack electrical connector
  3. Match previously marked spark plug wires to ignition coil and install
  4. Position water shield and install screws
  5. Install RH cowl panel
prev.gif next.gif

Aug 11, 2010 | 2002 Ford Taurus

1 Answer

Were are the spark plugs on a 2000 dodge intrepid r/t 3.5


Ignition Coil Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • The spark plug cables from coil pack
    • The electrical connector Coil Pack dod_intrpd_coil_pack.gif

    • The ignition coil fasteners
To Install:
  1. Install or connect the following:
    • Ignition coil fasteners
      1. Torque to: 105 inch lbs. (12 Nm)
    • The electrical connector Ignition Wire I.D. dod_intrpd_coil_pack_id.gif

    • The spark plug cables to coil pack
---
Ignition Coil-On-Plug Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Electrical connector from ignition coil. NOTE: On 3.5L engines, it is necessary to loosen the screws by alternating back and forth. Do not lose the spacers under the coil when loosening the screws.
    • 2 fasteners from ignition coil assembly
    • Ignition coil assembly.
To Install:
  1. Install or connect the following:
    • Ignition coil assembly
    • Screws
      1. 2.7L engine - 55 inch. lbs. (6.2 Nm)
      2. 3.2L engine - 60 inch. lbs. (6.7 Nm)
      3. 3.5L engine - 60 inch. lbs. (6.7 Nm)
  2. Connect the electrical connector.
prev.gif next.gif

Aug 10, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How do I change an ignition coil on a V6 1997 Grand Am?


Removal Procedure
  1. Remove all the electrical connectors at the ignition control module.
  2. Note position of spark plug wires for installation
  3. Remove the spark plug wires from ignition coils.
  4. Remove the screws securing coil assemblies to ignition control module.
  5. Disconnect coils from ignition control module. Installation Procedure
    1. Install the coils to ignition control module.
    2. Install the screws and tighten to 4-5 Nm (36-44 lb. in.) .
    3. Install the fasteners securing assembly to engine and tighten to 8 Nm (70 lb. in.) .
    4. Install the spark plug wires as noted during removal.
    5. Install the electrical connectors to the ignition control module
  6. Hope this Helps !

Sep 30, 2009 | 1997 Pontiac Grand Am

3 Answers

Coil pack. what and where is it? what does it look like?



 
 
Ignition Coil
Removal & Installation
4.2L Engine
1997-2000
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio ignition interference capacitor connector
The locking tabs
The six ignition wires, marking for reinstallation
The brackets
The spark plug wire set
CAUTION
Spark plug wires must be connected to the proper ignition coil terminal. Mark spark plug wire locations before removing them.
The accelerator cable bracket nut
The accelerator cable bracket bolt
The accelerator cable bracket and position it aside.
The two ignition coil nuts
The ignition coil stud bolt
The ignition coil
To Install:
Install or connect the following:
The ignition coil
The two ignition coil nuts
The ignition coil stud bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The accelerator cable bracket
The accelerator cable bracket nut
The accelerator cable bracket bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The ignition coil electrical connector
The radio capacitor connector


CAUTION
The Spark plug wires must be connected to the proper ignition coil terminal.
Squeeze the locking tabs and connect the six ignition cables.
2001-2003
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The spark plug wires, marking for reinstallation
CAUTION
The sparkplug wires must be connected to their correct ignition coil terminal.
The ignition coil
The bolts
Inspect the ignition coil for carbon tracks or damage.
To Install:
Inspect the ignition coil for carbon tracks or damage.
Install or connect the following:
The ignition coil
The bolts
Torque to: 53 inch-lbs (6 Nm)
The ignition coil electrical connector
The spark plug wires, in their original positions
4.6L Engine
1997-1999
To Remove:

NOTE: This procedure is for either RH or LH ignition coil.
Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires by squeezing the locking tabs (four each side)
CAUTION
The spark plug wires must be connected to their proper ignition coil terminal. Mark spark plug wire locations.
The bolts
The ignition coil
To Install:
NOTE: The procedure is for either LH or RH ignition coil
Install or connect the following:
The ignition coil
The bolts
Torque to: 44-62 inch-lbs (5-7 Nm)
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires (four each side), into their original positions by squeezing the tabs


CAUTION
The spark plug wires must be connected to their proper ignition coil terminal.

 
Top of Form 1
Bottom of Form 1

Mar 28, 2009 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
1999 Cadillac DeVille Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...