Question about 1992 Chevrolet Lumina APV

1 Answer

Aligning timing marks and how to check if its rite other than just the marks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

Cam gear dimple down & crank gears dimple up
6 o'clock & 12 o'clock respectively

Posted on Aug 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Aligning timing belt after breakage on 1996 toyota camry 2.2 liter 4 cylinder


Dustin, The attached links will explain timing alignment on 2.2 Camry engine. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Diagram of Timing Belt Marks and Installation
work on camry engine
Aligning timing belt after breakage on 1996 toyota camry 2 2 liter 4...
DIY GEN3 Timing Belt Waterpump Oil Seal Change Part 1 Toyota Nation Forum...

May 15, 2016 | Toyota Cars & Trucks

1 Answer

Need timing blet diagram 1992 ford ranger 2.3


Hi, the crankshaft marks are on the belt pulley and timing cover, so you have to mate it up to see them. The cam sprocket mark goes on the bottom, and aligns with another mark on the timing cover. There is a plug you pull out and hole to look thru to align the cam sprocket/shaft.


jturcotte_1801.gif


jturcotte_1802.gif


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Jun 01, 2011 | Ford Ranger Cars & Trucks

1 Answer

Need to know timing marks


REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt. Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.

INSTALLATION
1. Install tensioner pulley. Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
Do not add additional tension.
8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque:28~38 lb-ft (38~51 N·m, 3.9~5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on seal plate.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from tensioner installation.
Deflection pressure:22 Ib. (98 N, 10 kg)Deflection:0.39~0.50 in. (11~13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque:5.8~8.0 Ib-ft (7.9~10.7 N·m, 0.8~1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
15. Install water pump pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
16. Install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

INSPECTION
Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 in (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.

Feb 26, 2011 | 2002 Kia Spectra

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

1 Answer

How do i get the top 2 head pulleys align with the markings on the block? I ask this because the top left pulley will not align rite it seems to be spring loaded?


You need to hold it in place with a wrench while you install the timing belt. It springs back because it is just starting to open one of the valves. They make a tool that sits in between the two pulleys and locks them into place but you should be able to do it with the wrench as well.

Dec 07, 2010 | 1995 Acura Legend

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

3 Answers

Cant seem to time my 1990 subaru legacy


your timeing marks are on the block rite abouve the cams on either side and on the block in the middle but line the center mark on the teeth there is a mark not the arrow the arrow is where tdc is the mark is on teeth good luck.

Mar 26, 2009 | 1990 Subaru Legacy

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

Not finding what you are looking for?
1992 Chevrolet Lumina APV Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...