Question about 1993 Oldsmobile Bravada

2 Answers

I have a 93 Olds Bravada. The multi-function turn signal switch, the whole assembly including the turn signal switch arm needs to be replaced. I was told by one party that this part is non-replaceable and that the entire steering column needs to be replaced. Can this part be replaced by removing the steering wheel and and going in thru the inside of the steering column?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Oldsmobile Master
  • 2,050 Answers

I believe yes, you can replace just the switch. You will need to unplug the wire harness to the switch from under the dash/column area and fish it out, and the steering wheel will need to be removed.

Posted on Aug 27, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,074 Answers

I would assume it is but to make sure call a parts store and see if they sell the part, I do know that the air bag is a safety concern so be careful and good luck Tim

Posted on Aug 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My96 olds. Bravada blinkers wont work, when i turn on either blinker all 3 brake lights in back blink on and off (like emergencey flashers are on)I replaced both flashers andhave no burned out bulbs


You are going to have to register on BBB INDUSTRIES
FREE Documentation site...

because... These are REAL GM drawings &
Technical Service Bulletins... (TSBs).

Get onto your SIGNAL/BRAKE Schematic Drawing
and figure out where your "SHORT" (cross-over) is
happening...

This is where the REAL technicians use tone tracers...
and open circuits to halves (50, 50) to isolate FAULTED CIRCUITS.

If you don't "open" the circuits... the tone will travel
everywhere... or no where.

1996 OLDSMOBILE BRAVADA 4 3L V6 Turn Signal Switch RockAuto

1996 OLDSMOBILE BRAVADA 4 3L V6 Turn Signal Switch RockAuto 1996 OLDSMOBILE BRAVADA 4 3L V6 Turn Signal Switch RockAuto

Mar 19, 2017 | 1996 Oldsmobile Bravada

2 Answers

97 Olds Bravada wipers and turn signals not working properly


I agree, the multi-function switch would affect both components.

You could get a wiring diagram and test the circuits - or get a new switch and plug it into the harness.

Jul 06, 2012 | 1997 Oldsmobile Bravada

1 Answer

How much does it cost to repair a turn signal/light switch for a 2003 saturn


Is a multi-function switch? I have a 2003 Saturn LW200; I had to replace the headlight dimmer switch which is in the same assembly as the turn-signal switch. Fortunately I was able to find the part at a u-pull it yard and it cost $12.00. To buy it used through a parts store, it runs between $49.00 - $72.00 (includes any shipping charges). New, it will be around $134.00 and up.

Jun 05, 2012 | 2003 Saturn L-Series

2 Answers

Ford taurus hazard lights and turn signals not working


remove bottom screws under the steering wheel remove bottom cover and then the top cover where the turn signal arm sticks out . then remove the connector attached to the multi function switch at the turn signal arm. spray real good with circit cleaner . then put connector back on. should then ,if not replace the turn signal arm which has the multi function switch attached .about 50 dollars on a 96 taurus at auto zone.

Apr 13, 2012 | 2002 Ford Taurus

1 Answer

97 Olds Bravada My brake & hazard lights don't


There are TSB's for this issue. I chased this issue for months on mine. Go find the TSB's, there's troubleshooting pointing out the faulty part. It could be, the brake light switch, the hazzard light switch itself, the multi-function switch. I had replaced all of these and still had the problem. Wiring that goes from the brake switch to up near the fender was shorting against the fender. I replaced the pigtail, problem fixed. Best bet to help you, is find the TSB's for this problem.

Jun 28, 2017 | 1997 Oldsmobile Bravada

1 Answer

What are the instructions to remove and replace the combo turn signal switch, located in the steering column, for a 1999 bravada


Warning: 1995 and later models are equipped with an airbag. Always turn the steering wheel to the straight ahead position, place the ignition switch in Lock and remove key, then remove the airbag fuse and unplug the yellow Connector Position Assurance (CPA) connector at the base of the steering column before working in the vicinity of the impact sensors, steering column or instrument panel to avoid the possibility of accidental deployment of the airbag, which could cause personal injury. The yellow wires and connectors routed through the instrument panel are for this system. Do not use electrical test equipment on these yellow wires or tamper with them in any way while working under the instrument panel.
Caution: On models equipped with a Delco Loc II anti-theft audio system, be sure the lockout feature is turned off before performing any procedure which requires disconnecting the battery.

  • The turn signal switch function is incorporated into the multi-function switch, along with the wiper/washer and headlight dimming controls.
  • Disconnect the negative battery cable. Remove the steering column covers and the drivers knee bolster.
  • Remove the two Torx screws securing the multi-function switch to the top of the steering column.
  • Clip the wire-ties securing the multi-function switch harness to the other steering column wires.
  • At the bottom of the steering column, remove the bolt securing the large bulkhead electrical connector to the firewall.
  • Separate the two multi-function switch connectors from the large bulkhead connector.
  • The multi-function switch and its harness must be replaced as a unit.
  • Installation is the reverse of removal

Mar 16, 2011 | 1999 Oldsmobile Bravada

2 Answers

How to replace the turn signal switch in a 1992 Cadilac?


Turn Signal Switch REMOVAL & INSTALLATION CAUTION
Some models covered by this manual may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column, and instrument panel disable the SRS. Deville, Eldorado, Seville, and Fleetwood - Early Models
  1. Disable the SIR system.
    1. On Deville and Fleetwood, remove the left lower sound insulator. On Eldorado and Seville, remove the left side sound insulator.
    2. Remove the Connector Position Assurance (CPA) and detach the yellow 2-way connector at the base of the steering column.
    3. Remove the steering wheel.
    4. Make sure the ignition switch is in the LOCK position to prevent the SIR coil assembly from going off-center.
  2. Remove the SIR coil assembly retaining ring and the coil assembly. Allow the coil to hang freely. WARNING
    The SIR coil assembly will become off-center if the steering column is separated from the steering gear and is allowed to rotate or if the centering spring is pushed down, letting the hub rotate while the coil is removed from the column.
  3. Remove the wave washer.
  4. Use tool J-23653-C or equivalents, to depress the shaft lock, then remove and discard the shaft lock retaining ring.
  5. Remove the shaft lock.
  6. Remove the turn signal canceling cam assembly.
  7. Remove the upper bearing spring, upper bearing inner race seat and inner race.
  8. Move the turn signal switch to the RIGHT TURN position.
  9. On Deville, Fleetwood, and 1990 Eldorado, and Seville, remove the multi-function turn signal lever as follows:
    1. Make sure the lever is in the OFF position.
    2. Remove the access cover from the steering column housing.
    3. Detach the cruise control wiring connector. Note the position of the connector when installed in the column.
    4. Pull the lever straight out of the turn signal switch.
  10. On Eldorado and Seville, remove the multi-function turn signal lever as follows:
    1. On 1992-93 vehicles, slide the connector cover toward the front of the vehicle.
    2. Unplug the electrical connector. On 1991 vehicles, note the position of the connector when installed in the column.
    3. Push the lever straight in, rotate clockwise 1?4 turn and pull the lever out of the switch.
  11. On Deville, Fleetwood, and Eldorado and Seville, remove the screw, button, spring, and hazard warning switch knob.
  12. On Deville and Fleetwood, remove the one signal switch arm retaining screw. On Eldorado and Seville, remove the 2 signal switch arm retaining screws. Remove the signal switch arm.
  13. Remove the turn signal switch retaining screws.
  14. Remove the wiring protector and detach the turn signal switch connector.
  15. Gently pull the wire harness through the column and remove the turn signal switch. prev.gif next.gif

Nov 12, 2010 | 1992 Cadillac DeVille

1 Answer

1995 Olds. Achieva turn signals will not work


Did you replaced the bulbs?

Change the flasher relay...if thats not the problem replace your multi-function switch...

90's GM vehicles are known for their multi-function switches dying

Mar 23, 2009 | 1995 Oldsmobile Achieva

2 Answers

I need to locate and replace the multi function switch


My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Feb 27, 2009 | 1993 Oldsmobile Cutlass Ciera

2 Answers

On a 2000 olds Bravada the key wont turn off all the way


you need to replace the whole ignition switch assembly, the swtch may be secured with what you call shear bolts which may have to be drilled out, only you can decide if you are capable of doin this, new bolts should be supplied with the new swith, when you retighten the bolts, the heads will shear off when they are tight enough, the aim of these are to prevent theives making a quick ignition change to steal your car

Feb 16, 2009 | 2000 Oldsmobile Bravada

Not finding what you are looking for?
1993 Oldsmobile Bravada Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...