Question about 1993 Mazda 626

1 Answer

1993 mazda 626 not starting at first then after waiting about 1 seconds after trying it, will start right up. At about 5,000rpms car totally shut off. These conditions got worse... finally died. Whats the problem? Had oil on 2 of my spark plugs..could that be it? I replaced the fuel pump-didn't fix

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 22,114 Answers

Time to junk it i think ,never rev a car to this sort of engine speed either as you will damage things on an old vehicle

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 mazda 626 auto, starts fine when cold, but not when I've driven it for a while.


I would start with a good tune up, including the intake gasket. Changes in temperature could cause gaskets to stop sealing properly letting unmeasured air inside the engine. Also check for fuel filter.

Mar 26, 2013 | 1993 Mazda 626

1 Answer

Have a mazda 626 2000 4 cyl. when i run the car


your sylinoid on ur starter is going out

Jan 20, 2010 | 2000 Mazda 626

1 Answer

NEED TO KNOW HOW TO PROGRAM A REMOTE PAD FOR A MAZDA 626 EX 1995 PLEASE I REPLACED THE BATTERIES AND EVER SINCE THEN THE REMOTE DONT WORK


1. Remove key from ignition.
2. Close all doors.
3. Open driver side door and leave open.
4. Insert key in ignition, Turn key to ON (as far as you can go without starting the engine) and OFF, Remove Key.
5. Repeat step 4 two more times, making sure you remove key each time.
6. Close and then open the driver’s door three times.
7. Buzz sound or chime should be heard at this point signaling that the vehicle is now in programming mode. If not,
wait 40 seconds and return to step 1.

8. All transmitters need to be programmed at this time, including the old ones. Push any button on a transmitter two
times. A buzz sound to chime should be heard at this point signaling that the vehicle has accepted the new
transmitter code. Repeat for next transmitter, up to a total of three remotes (including any old remotes).

9. After all remotes are programmed, wait 15 seconds or until you hear four chimes signaling successful
programming.

Good luck and this should work.

Dec 09, 2009 | 1995 Mazda 626

3 Answers

What is the oil capacity of a mazda 626 LX


2.0L - 3.7 quarts.
2.5L - 4.2 quarts.

Nov 28, 2009 | 1994 Mazda 626

1 Answer

White smoke on start up on 1998 mazda 626


Hi
Lots of things to check
?Leaking head gasket
Does it use brake fluid
Start engine only fo a few seconds, shut down, remove all spark plugs to see which ones are fouled

Aug 10, 2009 | 1999 Mazda 626

1 Answer

1993 mazda 626: could not get trans out of park!


Ignition lock is activated: You over rode it but still have original problem. Alarm system might be confused. SO....

1 disconnect battery negative (-) cable(make you have radio code if any) to reactivate radio, which works anyway if code was never set.

2 press brake peddle for 5 seconds

3 reconnect negative cable to battery.

use key and twist diver door lock to OPEN (this resets alarm which might have caused ignition lock module to activate.

You should be able to turn on the ignition, start the engine and shift out of park. Hope this helps.

Jun 10, 2009 | 1993 Mazda 626

1 Answer

1993 mazda 626 battery goes dead and it overheats


That second Problem IS The Waterpump. As for the First Problem, You may need to replace the Belt and Belt Tensioner. If the Tensioner is Bad it will allow the Belt to slip and will Not allow the Alternator to Recharge the Battery. For that Matter it Could cause the Overheating Also. I would go with the Belt and Tensioner First and see where you are.

Jan 23, 2009 | 1993 Mazda 626

1 Answer

My 1993 Mazda unextectedly stops running


check wires on the battery make sure tight and try to find out what wires are luse and let me know ill help u out

Jan 02, 2009 | 1993 Mazda 626

Not finding what you are looking for?
1993 Mazda 626 Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...