Question about Isuzu Trooper

1 Answer

How do I get the front rotors off.I have the pads and calipers off but the rotor want come off. HELP!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

First spray wd-40, PB-blaster, or any other kind of lubricant on the wheel studs that come through the rotor and spray behind the rotor where it meets the hub the best you can. Let it sit for a little bit, then start pounding on it with a rubber mallet. If it is really held on there spray more lubricant and keep punding on it. Don't be afraid to really hit it, depending on how bad it is stuck on there, it may take awhile. Good luck. Hope this helps.

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

Chrysler caliper bracket


you will need the rotors, calipers, brackets, and pads off of a 300c

Apr 28, 2013 | Cars & Trucks

1 Answer

Should the center spindle nut and 2 torgued phillip head screws be removed to replace front brake rotor on 1999 honda accord lx


will try to help. 1st remove the wheel, then remove the 2 caliper bolts that hold the brake caliper on. after removal of brake caliper, [it should just pull off after the 2 bolts are removed] replace the brake pads[be sure to apply anti squeal lube to the outer side of the pads..not the pad itself,the one not contacting the brake rotor] install the pads, the you will need a C clamp to push the brake caliper pistons back into the caliper. i've used this installation easily. use the old pad ,place it against the caliper piston,then apply the C clamp and push the caliper piston back into the brake caliper, then the brake caliper will slide back over the new pads easily, no need to bleed the brakes if you use this solution. replace the brake caliper bolts, then go to next side and repeat the process. after the replacement of the front brake pads,pump the brakes with engine running!!! it's really a simple process. be sure the brake pads are facing the brake rotors with the [pads] facicing the rotors. no metal facing metal. easy! if you have added brake fluid recently, do not be alarmed if you see fluid coming out of the brake master cylinder,when you use the C clamp to collaspe the brake caliper back into the recessed position. [as always when you have to add brake fluid to the brake master cylinder,it only means your brakes are wearing naturally. if you have a vibration in front wheels or steering wheel when braking, you have a brake rotor or both front brake rotors that need replacement with your brakes also. hope this helps and as always, please get a second opinion if you have doubt. an expert will be happy to help. thank you for choosing fixya.com

Dec 22, 2010 | 1999 Honda Accord

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

2 Answers

When first applying the brakes there is a shuttering in the front end. After this it goes away and the car stops fine.


you need new brake pads and rotors and possibly calipers, the rotors are most likely warped. or the pads are worn enough where the caliper piston extends to the limit and is not stable in the caliper and wobbles.

Apr 24, 2010 | 2000 Ford Excursion

1 Answer

How to replace front rotors on a 1989 190e mercedes?


Remove tyres. Remove brake pads.
Remove Brake calipers bolts from the back of calipers.
Put calipers aside without removing brake lines. Remove rotor bolts. Remove rotors. Install new rotors Make sure new rotors are clean from any grease that comes on it with petrol or any cleaning chemical for that purpose (no water) Install calipers Install new brake pads Good luck

Oct 20, 2009 | 1989 Mercedes-Benz 190

1 Answer

How to change brake pads on 1996 roadmaster


Disc brakes I assume on the front of the car? If so.

1. take off front wheel.
2. remove 2 bolts that hold the brake caliper on the rotor.
3. slide the caliper off the rotor and remove old brake pads.
4. take a C-clamp and put it so you can press the piston back in on the caliper so it is almost all the way in. (Caliper = The round shaft that is on the inside of the rotor that pushes out the pads causing the resistance).
5. Check the condition of the rotor. If it is smooth and doesn't have too much of a lip on the outside of the rotor(both inside and outside of rotor), then put the pads on the caliper and put it back together.
6. If rotor is rough or has grooves in it then take the two bolts out so you can remove the caliper bracket from the wheel assembly. Tap on the rotors till they loosen up an replace them.

Good Luck...you can do it

Oct 09, 2009 | 1992 Buick Roadmaster

1 Answer

Intructions to replace front pads and rotors Corolla


take off tires. two 14mm bolts behind the caliper. loosen the bottom 1. tilt the caliper up. slide caliper inward of the car, let caliper hang. two 17mm bolts behind the bracket take it off. and rotors should slide out. if rotor seized spray WD40 and hammer the rotor. careful don't hammer the stud it will screw up the thread.

Jul 31, 2009 | Toyota Corolla Cars & Trucks

3 Answers

2006 subaru legacy remove front brake rotor


Hello, hope this info helps...(subytech1)...



REMOVAL
15-INCH TYPE

  1. Lift-up the vehicle, and remove the front wheels.
120334720


  1. Remove the caliper body and the support from housing, and suspend it from strut using a wire.
120334721


  1. Remove the disc rotor. NOTE: If the disc rotor seizes up within hub, drive the disc rotor out by pushing with an 8 mm bolt in holes B on the rotor.
  2. Clean mud and foreign particles from the caliper body assembly and the support. 16-INCH TYPE Refer to 15-inch type. 17-INCH TYPE Refer to 15-inch type.
INSTALLATION

  1. Install the disc rotor.
  2. Install the caliper body and the support to housing. Tightening torque: 80 Nm (8.2 kgf-m, 59 ft. lbs.)
  3. Install the front wheels.

Mar 27, 2009 | 2006 Subaru Impreza

1 Answer

1993 Jeep Cherokee Front Rotor & Pad Replacement


This is a walk through for a 1993 2wd.

1. Jack up and remove tire
2. Remove 2 brake caliper mounting bolts
3. Remove caliper and hang out of way with wire
4. Remove rotor, if stuck hit on all sides with a rubber mallet until it breaks loose.
5. Install new rotor
6. Remove old pads from caliper
7. Using a c-clamp and a block of wood against caliper piston, compress piston until it is flush w/caliper
8. Install new pads in same location as old pads
9. Reinstall caliper, may have to nudge it into place with rubber mallet
10. Reinstall tire.

note: There are no bearings to grease. You must replace the entire hub assembly if yours are worn.

Jul 01, 2008 | 1993 Jeep Cherokee Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...