Question about 2002 Ford Taurus

1 Answer

Replacing the cam sensor where is it - 2002 Ford Taurus

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Expert
  • 1,868 Answers

Hello! Remove accelerator cable snow shield...Disconnect cables from throttle body...Remove throttle return spring...and cable bracket...Remove spark plug wire retainer...Remove wiring harness from intake manifold support and position out of the way...Release fuel injector wire harness from valve cover studs and position out of the way...Disconnect Camshaft Positioning (CMP) connector Remove the screws and CMP...Guru..Saailer

replacing the cam sensor where is it - fee46b1.gif

Posted on Aug 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No fire to coils after cam position sensor replaced in 2001 Audi a6 quattro


Throwing any codes? Crank sensor working? The cam and crank sensors typically work together to adjust timing.

Aug 02, 2016 | Audi Cars & Trucks

1 Answer

1991 olds 98.3800 motor. Where is the cam sensor?


it is located on the timing cover at the top. there is a plug connected to the sensor, its usually a 90 degree connector. there is also a magnet that is attached to the cam gear that sometime breaks off causing a cam sensor code to be set. with the cam sensor out using a mirror look into the hole and turn the engine over checking to see if the magnet is still fastened to the cam gear. the only way to replace this magnet is to replace the cam gear. in which case replace the timing gears and chain at the same time. the timing cover must come off.

Aug 16, 2014 | Cars & Trucks

2 Answers

2007 pontiac, solstice cam sensor replacement -is this common?


replace crank senser, first, always replace together, also chk some time double cam motores have to cam sensers.

Mar 17, 2013 | 2006 Pontiac Solstice

1 Answer

2000 dodge neon will not start unless the cam shaft sensor is unplugged


I would go and but a cam sensor from the dealer. Aftermarket cam sensors can be slightly irregular. I had this happen to me with an aftermarket ABS sensor on a chevy. The whole problem was a gap difference equal to two sheets of paper. Whats happening is there is an open circuit in your old sensor that causes the check engine light but the new one has a good circuit but bad reading. I would say that is your problem.

Jan 29, 2012 | 2000 Dodge Neon

1 Answer

Hi My car engine just died on highway. Check engine light came on. Diagnostic showed P0340 CAM sensor error. Got it replaced but error still there. Got Fuel filter and the sensor on the engine Oil cae(...


The cam sensor is supplied a reference voltage by the engine computer and the cam sensor should generate a signal back to the engine computer above 50 rpm of the engine cranking. The problem could be a faulty purchased cam sensor (yes this happens sometimes although rare) fwiring connector problem at cam sensor or faulty engine computer.

May 29, 2011 | 2004 Chrysler Sebring

1 Answer

I have a 91 olds Ninety eight regency elite Intermittently dies code 41 comes up cam sensor circut replaced cam sensor still dies could it be the crank sensor? thank you Michael Dale


cam sensor is only half of the cam circuit, the other half of the cam circuit is the magnet on the timing chain. the cam sensor reads from the magnet every time the engine completes a revolution,
what happens is the magnet on the chain will break into smaller piece which makes the sensor harder to read every time the engine make a complete revolution.
most likely you'll need to replace the timing chain to fix this.

Oct 12, 2009 | 1991 Oldsmobile Ninety Eight Regency

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

2 Answers

Cam shaft sensor replaced


the crankshaft sensor needs to be replaced.you could have purchased a faulty sensor,

Jun 12, 2009 | 2004 Dodge Stratus

1 Answer

2003 stratus both sensors replaced still unresolved


Have the exact problem. Replaced cam sensor and timing belt. Still happens intermittently. code is p0344.

May 30, 2009 | 2003 Dodge Stratus

Not finding what you are looking for?
2002 Ford Taurus Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...