Question about 1998 Hyundai Tiburon

Open Question

1998 hyundai tiburon starter removal.Bottem bolt and power wire off but I can get to the top bolt.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1998 kia sportage, how to replace the starter?

1. you have to remove the possitive on the battery.
2. lift the truck on the passenger side. (remember to use jack stands for security)
3. remove the wires going to the starter. (there should be 2 wires.)
a) a thick wire, thats the possitive.
b) a thin wire thats the starter signal from ignition switch.
4.remove the bolts holding the starter, you should see them they are the only ones touching the starter base.
5.you can sheck if yours is good at anu(advance discount auto parts).
6.do the same steps from four to one to install the new starter.

Posted on Jan 13, 2009

  • 1861 Answers

SOURCE: removing starter from toyota corolla 1998

No. Removal of the intake manifold is not an attractive option.
...That will cost you more time and money in the long run.
You will need to replace the intake manifold gasket, and several others.

Posted on Jan 15, 2009

  • 260 Answers

SOURCE: any holes in firewall without drilling to run power wire for amp

Best way is through the rubber caps look for em there are up there.

Posted on Apr 11, 2009

  • 69 Answers

SOURCE: change water pump on 2001 hyundai tiburon

It is a 2.0L (the delta blocks weren't in tibs until '03). You have to remove the timing belt tensioner, and then you can remove the bolts for the water pump. I would strongly recommend not only taking careful precaution not to disturb the orientation of the gears in this process, but also to replace the timing belt and water pump at the same time. You don't want to go through this process all over again do you?

Posted on May 27, 2009

  • 299 Answers

SOURCE: 93 saturn twin cam starter removal

Top bolt is almost dirrectly above bottom bolt but,toward engine about 1 inch. slip 13mm.socket with enstention behind starter solenoid ,you have to fish for this bolt.Very hard if you do not have a rack,We always remove it from bottom.

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am replaceing the starter on a 1998 toyota corolla 1.8 ltr. How do I get to the top bolt on the starter to remove it ?


Hello,

To replace the starter of a 1998 toyota corolla, please follow the steps below:
  1. Remove the key from the ignition, and remove the battery, do not attempt this with the battery in car.
  2. Remove the battery and tray.
  3. Look to the rear of the engine, You'll see the top of the starter, loosen and remove the 14mm bolt/nut holding it down below,
  4. Drain the radiator and remove the lower radiator hose. This will let You squeeze the starter around the AC line,
  5. Then install the new starter, the one bolt You removed from the bottom, screw the last 14mm bolt on the starter into the transmission loosely,
  6. Go up top, reinstall the top bolt, tighten this firmly but not all the way,
  7. Go below, tighten the bottom bolt to final spec.
  8. Reattach all the wires, make sure the trigger wire is snapped in fully.
  9. Go up top, firmly firmly tighten to spec the top bolt,
  10. Reinstall everything You removed up top the below,
  11. Reinstall the battery and make sure the ignition is off while doing this,
  12. Hook up battery and ensure every thing that was loosened has been installed back on.
  13. Then You crank it to see if it will start.
Hope this helped. Thank You for using FixYa!!!

Jan 26, 2011 | 1998 Toyota Corolla

1 Answer

Removing front rotors?


Remove tire,
Remove caliper,
Remove the 2 bolts holding the knuckle to the strut,
Remove the knuckle from the lower ball joint,
Should be 2 or 3 more bolts to remove from the knuckle after it is completely free.

Oct 15, 2010 | 1998 Hyundai Tiburon

1 Answer

I NEED TO KNOW THE EXACT LOCATION OF WHERE THE CRANKSHAFT POSITION SENSOR IS LOCATED ANY HELP WILL BE GREATLY APPRECIATED THANKS?


Remove negative battery cable. Remove heat shield from starter. Remove battery cable from starter lug and single wire connector to starter solenoid. Remove starter. Above starter is CRANKSHAFT POSITION SENSOR. Disconnect sensor connector right below ignition coil assemble from top of engine. Slide sensor connector out of U-shaped bracket. Loosen 10mm bolt securing sensor. Lubricate new sensor O-ring with vaseline and install. Reverse procedure to finish job. I just did the job on my 03 Tibby 2.7liter today. Note: Make sure you press the new sensor in by hand and be sure it is seated all the way before you tighten the 10mm bolt, otherwise the sensor mounting tab make distort and crack and the sensor may not be in all the way. Good luck!

Oct 13, 2010 | 2003 Hyundai Tiburon

1 Answer

I need to replace a 2001 hyundai tiburon starter


Hi, Disconnect car battery.
Remove cover from air intake. Remove Filter.
Remove Filter intake housing (3 inner bolts) and large hose at the furthest screw collar. (This is important as you will need to reach the bolts to the starter by reaching from the top down via that location)
Remove the starter/ acceleration cable (1 bolt at the end of the cable, 2 bolts at the guide point screwed intot the engine block)
THE STARTER IS LOCTED AT THE BACK OF THE ENGINE WITH ONLY 2 BOLTS HOLDING IT IN PLACE
Remove the 2 bolts about half way with a socket wrench, remove the bolt sthe remining way with hand or open end wrench. (This is necessary especially on the lower bolt as there is liited work space.)
Take hold of the the starter using a partially blind reach and patially pull it out slightly turning it around so you can see the connectors.
Remove connectors........ Remove clip, the the bolt that holds the positive cable.
You can now fully remove the starter.
Take it 2 the local auto parts to have it tested. Have them test it 4 to 5 "bumps" as when mine was initially tested it worked fine but after 2 to 3 more attempts it froze and would operate.
To reinstall reverse procedure
Take care

Jul 30, 2010 | Hyundai Tiburon Cars & Trucks

1 Answer

How to replace starter motor on golf mk 4


Before you start, disconnect the negative terminal of the battery. Unplug clip on plug from starter solenoid. Remove nut for battery cable on starter solenoid. Remove nuts on starter mounting bolts that hold the brackets for the wiring harness [top mounting bolt] and the power steering pipe [lower mounting bolt]. Lastly remove the starter mounting bolts and remove starter. Re-assemble in reverse order.

Jun 11, 2010 | 1998 Volkswagen Golf

1 Answer

How do I remove my backseat from my Hyundai Tiburon


normally you will have to lay the backs down and lift the little velcro strip up. There should be two bolts on the back of each section. Once the bolts are out you can just slide the two section straight out- towards the windshield.

The bottom section is held in by two or three bolts that will be exposed now that the seat backs are gone. There will also be two metal clips sticking out from underneath the seats that need to be pulled out before the seat will come free.

Good luck!

Feb 06, 2010 | 1998 Hyundai Tiburon

1 Answer

My boyfriend has a hyundai tiburon 1998 and the it shifts to 3/4 gear. A mechanic told him it needed an input/output sensor but we can't find it anywhere. So,we called the dealer and they say it doesnt'...


It is easiest if you take the air filter and its casing off. use a 8mm wrench to disconnect the top of the case. there should be three 10mm bolts holding the bottom of the case to the frame. Once the air filter case is off the speed sensor connection is almost directly under it, slightly more towards the engine, on top of the automatic transmission. A 1998 Tiburon has a pulse generating speed sensor, which means there is only one connection to deal with, but it has two sensors which bolt onto the transmission. To remove the old sensor, press the release pin on the connection, to do this I use a small Allen wrench. It is easiest to follow the lines of the old sensor to find where the two sensors are to be placed. Once the two sensors are found, they can be removed using a 10mm wrench. it may be easiest to replace the far sensor with the driver side wheel removed, or at least the car should be elevated.Good luck and keep me posted.

Jan 18, 2010 | 1998 Hyundai Tiburon

1 Answer

How do i change the spark plugs


if its a four cyl remove upper coveron top af engine has 6 10mm head bolts pull up the wires to find plugs-caution dont chang plugs without doing wires,the newer version has coil on plug just remove coil pack,should have four with 10mm bolt holding them on,remove bolt and pull up on coil pack

Oct 08, 2009 | 2006 Hyundai Tiburon

2 Answers

Changing the starter in a 1994 Toyota Corrolla


you need to remove one bolt from the top and the other from the bottem. also the wires are removed from the bottem. most likey the starter if factory is still good the starter contacts wear out they are under the cover on the back of the starter.

Apr 18, 2009 | 1994 Toyota Corolla

1 Answer

2003 tiburon transmission


if you have a 4 cylinder you wiggle the clutch shaft up and down remove the lever and this will get the fingers off the releasbearing / 2 starter bolts 2 large bolts up top 3 under exhaust and 4 0n the other side lower one is above right inner cv axle, remove left axle from car right axle can moved over un do ball joint 3 mounts remover upper side and reaar , strap engine to a cradle or 4,4 post chained to support engine you can slide tranmission over14 inches with room to stick your hands in and remove pressure plate ,fly wheel can be removed but takes good hands tricky,now thats a hyundai flat rate tech procedure for 4 cyl, IF YOUR NOT SURE ABOUT or if the engine is V6 cylinder THE SUB FRAME COMES OUT you can remove rack hose on sub frame and 4 bolts and wire or strap the steering rack to body at that can stay in car or you will have to take rack out with sub frame

Sep 25, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
1998 Hyundai Tiburon Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...