Question about 1992 Ford Ranger

1 Answer

Is the ignition key the same as the door key on a 1992 ford ranger pick up ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

No, there are two different keys: the door key is usually round where the Ford emblem is and the ignition is square. Also, the shape of the keys are such that the door key cannot be inserted into the ignition and vice versa. Hope that helps.

Posted on Aug 29, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my ignition switch sticking?


You could try graphite in the cylinder, but it is a common problem on older Fords, usually resulting in changing the lock cylinder,

Aug 24, 2014 | 1992 Ford Ranger

1 Answer

What are the speaker sizes in 1992 Ford Ranger 3.0


The front door speakers are 5.25" (6.5" can be made to fit). The rear speakers (if equipped) are 6x8".
Source: 30 years experience in the Mobile Electronics industry, Owner of PowerSounds Mobile Electronics, and owner of a 1992 Ford Ranger standard cab.

Apr 04, 2013 | 1992 Ford Ranger

1 Answer

My 92 ford ranger sometimes acts like its not running on all four cylinders what could be the problem for this? I replaced plugs and wire and put two new ignition control modules in and didnt do a thi


sounds like the pick-up coil in the distributor. when pick-up coil goes bad they sometimes have intermittent electrical contact, therefore causing veh to run rough at times, and fine at some. it will eventually go out totally.

Aug 27, 2012 | 1992 Ford Ranger

1 Answer

What is the specific ignition control module number for a 4-cylinder, 2.3 liter Ford Ranger?


I recommened only the factory part for this. You can buy it from most full service part stores and not just the Ford dealer. The part is
MOTORCRAFT Part # DY959 [ICM] (Ignition control module) $176.79
You can also mail order it from a site I use called rockauto.com the price given above is from that site.

Feb 19, 2012 | 1992 Ford Ranger

1 Answer

Ignition switch cylinder has been replaced but problem remains. I turn key to 'on', everything normal. When I turn key to 'start' there is no resistance or springback and starter does not engage. 1992...


Check ignition switch, the switch sit on the steering colum, under the dash, on the top side of the colum, make sure the rod that come's from the key is still in the switch, you will have to remove switch to check, held on with two small screw's, after removeble of switch, with screw driver work switch, if it don't feel spring like, switch is bad

Aug 20, 2010 | 1992 Ford Ranger

2 Answers

My 1995 ford ranger pick up speedometer, radio, break lights, wipers and turn signals dont work


On the ford ranger wiper motor not working, this is how u fix it. I am a licenced autobody mechanic for mercedes and my son bought a ford ranger and of course the wipers were not working-neither did the dome light and door chime.I told my son too replace all fuses ,switch and motor. And still nothing.Remove radio there is a pcm in behind- ours was unpluged. When we plugged it in the door bell would not shut off and the dome light stayed on. In stead of unplugging the pcm remove the light if wd40 does not work on the door latches. And to stop the door bell ringing remove the plastic cover around the ignition and their is a single wire with a blue connector just remove the wire it is the wire closest to the key and tape up the end and problem solved guarenteed . my email is frameman127@yahoo.ca I will walk u through it .

Jul 24, 2010 | 1995 Ford Ranger Supercab

1 Answer

How to remove an ignition lock cylinder on 1991 ford ranger without the keys.


hard! there is a hole on the steering column near the lock cylinder. normally you can turn the key and stick a small screw driver in it to pull out the lock cylinder. in this case you can drill the pin through that hole then pull it out

Feb 26, 2010 | 1992 Ford Ranger

1 Answer

I lost my Ignition key for a 92 ford ranger. How would i go about rying to get another one without a spare?


call your dealer with your vin number and see if maybe they can help ,if not call local lock smith to have them make one from your ignition,with a mold

May 11, 2009 | 1992 Ford Ranger

1 Answer

How to remove and replace ignition switch


the ignition switch is bad if the silver part spins all the way around. you will need to replace it.

Oct 26, 2008 | 1992 Ford Ranger

Not finding what you are looking for?
1992 Ford Ranger Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...