Question about 1983 Ford Fairmont

Open Question

I replaced the fuel pump on 98 XH Longreach Ute and even though car is running again now the fuel consumption is worse and the pump is making a winding noise like its searching for fuel?

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22246 Answers

SOURCE: "99 ford tradesman ute longreach. Excessive fuel

cold start temperature sensor is my first suspect

Posted on Oct 31, 2010

Ad
  • 20 Answers

SOURCE: ford longreach with rough idle

a diagnostic computer check from your local ford dealer will sort that problem for you,the cost for that check should be around $50 and from then on whatever the problem wil cost you whatever your local dealer charges for labour or unless of course you are able to do it yourself which is cheaper in the long run,hope that helps,,goodluck.

Posted on Nov 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am replacing the engine in my xh ute . I have been told el engines fit. I have fitted el tickford engine . It fits ok , but runs ruff, do i need to use ecu from original el or can i use xh one ?


You need to use the ECU from the engine that you installed You might be able to go to a dealer and get the ECU programmed to run the new engine

Nov 06, 2015 | Cars & Trucks

1 Answer

Does an xh ute have the same fuel gauge for gas and petrol. When I change to gas my fuel gauge drops to empty????


Don't know the vehicle at all, but perhaps the gas (I assume you mean something like lpg) gague is sharing the same power set up, ie when switch to gas, the power or sensor wires are then redirected elsewhere, so the fuel gague drops off, till returning to petrol.

See this scenario on a couple of lpg cars here in uk. All lpg cars I've seen do not share a gague though.

May 29, 2015 | Cars & Trucks

1 Answer

96 xh ute won't start when warm


I would check all the fuses. I pull them and look. This takes care of any corrosion problems. Which sounds like what you have. Also check the main plugs for the coil and injectors for corrosion.

Jan 31, 2015 | Cars & Trucks

1 Answer

Diagram xh ute fuel pump location


go to www.automecanico.com and fix it. Translate this amazing webiste with your browser.
God bless you

Jul 10, 2013 | Cars & Trucks

1 Answer

Oil is mixing with diesel then splashes out


Need more input here iam afraid ,like make and model and where the leak is if the fuel is mixing with oil do not drive it could hydraulic or even worse run away with itself and just run till it blows up ,once it goes turning the key off will not stop the engine it will run on the sump oil mix and watch a con rod come through the block

Apr 13, 2012 | Cars & Trucks

1 Answer

"99 ford tradesman ute longreach. Excessive fuel


cold start temperature sensor is my first suspect

Oct 31, 2010 | 1999 Ford Super Duty F 550

1 Answer

How do i stop the fuel running when changing a fuel filter? 1996 ford xh longreach. 4.0l v6


You can clamp it if it is a rubber tub. But if it's metal. fuel should only spill for about 30 seconds until the line is empty. Be careful! Have a mechanic do it if you don't feel comfortable doing it. Thanks for asking!

Jun 29, 2010 | 1996 Ford Aerostar Extended

1 Answer

Ford longreach with rough idle


a diagnostic computer check from your local ford dealer will sort that problem for you,the cost for that check should be around $50 and from then on whatever the problem wil cost you whatever your local dealer charges for labour or unless of course you are able to do it yourself which is cheaper in the long run,hope that helps,,goodluck.

Nov 26, 2008 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...