Question about 2005 Chrysler Sebring Conv

Open Question

I got the code back p0572 dealing with my brake switch

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 60 Answers

SOURCE: code p0572

That's probably a fairly easy fix it job you just need to check the fuse and relay for the cruise control , plus check the black wire going to the cruise control servo unit under the hood , you'll see two thin metal cables running to it from the throttle body.Plus this code suggests that the switch on the brake pedal might be acting up or that the switch is loose of out of alignment or it has a bad ground etc, also it mentions low current that's probably a bad connection of faulty wire and again ground related.

Hope that helps and best of luck.By the way most of such problems if related to wiring are ground faults.If it is the brake switch etc you can check with the big auto wreckers for the part bec they know what parts are interchangeable on what models and yrs etc.I suggest getting the used part from a U pick wreckers if at all possible bec if you remove the part you can save up to 50% on the parts over all average price or cost.

Posted on Aug 16, 2009

Ad
  • 634 Answers

SOURCE: chrysler code P0572 need help

Trouble Code: P0572

Brake Switch Signal No. 1 Circuit Low

Trouble Code Conditions:Ignition is on. When PCM recognizes that brake switch is mechanically stuck in the low/on position, a DTC will set. Three global good trips are necessary to turn off MIL.

Possible Causes:

* Brake switch signal circuit is shorted to ground
* BS No. 2 signal open
* Brake switch is damaged or has failed
* PCM has failed

i would check the brake switch first located under dash and when brake is pushed it hits switch turn ignition on and test the wires if all hot then switch is bad, other wise there is a short or bad pcm and these are not easy fixes requires knowledge of car wiring and diagnostic tools/computer

Posted on Jul 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0572 Brake Switch A circuit low error code.


code p 0572 refers to cruise/brake switch A --circuit high===causes---wiring short to positive ---cruise / brake switch---ECM
replace the brake switch first as it gets the most work , then the cruise control switch also on the brake

Nov 29, 2015 | 2010 Jeep Grand Cherokee Laredo

1 Answer

Is it safe to drive my jeep with this p0572 code


what year ? where did you get this code ? motor size ? model

Oct 15, 2014 | Cars & Trucks

1 Answer

What does P0572 mean on a 2009 Dodge Charger


According to my code book it is a Brake Switch A Circuit Low input. Sorry that's all i have

Nov 14, 2012 | 2009 Dodge Charger

1 Answer

I need to know what trouble code p0572 is for a 2004 dodge stratus 4 cyl. ?


P0572 Cruise Control/Brake Switch A Circuit Low. here is a cause/solution for your problem even though it is for a Chrysler it is the same code and fix. Good Luck Tim

http://www.helpforcars.net/obd_codes/P0572_chrysler.html

Apr 30, 2011 | 2004 Dodge Stratus

1 Answer

I have got a problem with my 2007 model subaru impreza, i do not know what happened but it has deleted my dashboard dump!! gives error code p1572, and car doesnt start how can i fix this problem


well this code doesnt show under subaru and on generic codes it shows as

P0572....Cruise Control/Brake Switch A Circuit Low, which i dont think is your problem so i would hazard and say that something serious has gone wrong like the ECU unit and its thrown the immobilisor on so i think you will have to have the vehicle taken to a dealer and be prepared for a nice big bill

Jan 27, 2011 | Subaru Impreza Cars & Trucks

1 Answer

Trouble code po572 on dodge dakota slt, 3.7 ltr


P0572 - Cruise Control/Brake Switch A Circuit Low

Switch number 1 on the cruise brakes has low voltage on the circuit. Or how about low voltage on your brake line switches or something? Check to see if inadvertantly the connection to the actual pressure switch (one for front & the one for the rear) may have pulled loose at the switch. These are located in the Hydrolic fluid line... Trace from calipers back. (Two wire connection).

Tell us news.


Aug 02, 2010 | Dodge Pickup Cars & Trucks

1 Answer

Code p0572


That's probably a fairly easy fix it job you just need to check the fuse and relay for the cruise control , plus check the black wire going to the cruise control servo unit under the hood , you'll see two thin metal cables running to it from the throttle body.Plus this code suggests that the switch on the brake pedal might be acting up or that the switch is loose of out of alignment or it has a bad ground etc, also it mentions low current that's probably a bad connection of faulty wire and again ground related.

Hope that helps and best of luck.By the way most of such problems if related to wiring are ground faults.If it is the brake switch etc you can check with the big auto wreckers for the part bec they know what parts are interchangeable on what models and yrs etc.I suggest getting the used part from a U pick wreckers if at all possible bec if you remove the part you can save up to 50% on the parts over all average price or cost.

Aug 16, 2009 | 2004 Dodge Stratus

1 Answer

Chrysler code P0572 need help


Trouble Code: P0572

Brake Switch Signal No. 1 Circuit Low

Trouble Code Conditions:Ignition is on. When PCM recognizes that brake switch is mechanically stuck in the low/on position, a DTC will set. Three global good trips are necessary to turn off MIL.

Possible Causes:

* Brake switch signal circuit is shorted to ground
* BS No. 2 signal open
* Brake switch is damaged or has failed
* PCM has failed

i would check the brake switch first located under dash and when brake is pushed it hits switch turn ignition on and test the wires if all hot then switch is bad, other wise there is a short or bad pcm and these are not easy fixes requires knowledge of car wiring and diagnostic tools/computer

Jul 09, 2009 | 2004 Chrysler PT Cruiser

2 Answers

Abs light emergency light stay on


Hi, You should check for a sligt break fluid leak from the break light switch (attacked to the master cylinder). Yeah, I know this seems strange, but on my 2001 this leak caused all types of problems with lots of dashboard indicators. The leaking switch was a recall for Ford Trucks, but not the minivans. Hope this helps

Oct 08, 2008 | 2001 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...