Where can I find the 2 steel brake lines that go from the master cylinder to the abs and the 2 that go from the abs to the front wheels?

Something is wrong with your statement
it is a 99 caravan 3.3 no abs , then you are on about abs light pump etc
the abs pump only works when the master cylinder is under pressure and that pressure is suddenly reduced by the sensor reading a locked wheel and a valve is opened to release line pressure to that wheel As soon as that wheel starts to turn, the valve closes
while the wheel is stopped and that valve is open , the abs pump kicks in to maintain line pressure otherwise the brake pedal would go to the floor
master cylinders work through a. abs unit and not because of it so if the master cylinder becomes faulty, the abs pump will not operate until a wheel stops turning as there is no line pressure to stop a wheel turning
the abs light may not be on because there is nothing to operate the system to put it on

Ok here is what you have to do. First off make sure your master cylinder is full, Second your vehicle must be running when you bleed brakes that is equiped with ABS this allows the ABS pump to to run you must bleed both front brakes starting at the passenger side wheel then moving to the drivers side. It will take quit a bit of bleeding and be sure to keep checking fluid level in master cylinder well bleeding. Just remeber the vehicle must be running while bleeding the brakes.

The brake system bleeding procedure differs for ABS and non-ABS vehicles. The following procedure pertains only to non-ABS vehicles. For details on bleeding ABS equipped vehicles, refer to the ABS procedures later in this section.

WARNING Make sure the master cylinder contains clean DOT 3 brake fluid at all times during the procedure.

1. The master cylinder must be bled first if it is suspected of containing air. Bleed the master cylinder as follows:
   1. Position a container under the master cylinder to catch the brake fluid.
   2. Loosen the left front brake line (front upper port) at the master cylinder and allow the fluid to flow from the front port.
   3. Connect the line and tighten to 24 ft. lbs. (32 Nm).
   4. Have an assistant depress the brake pedal slowly one time and hold it down, while you loosen the front line to expel air from the master cylinder. Tighten the line, then release the brake pedal. Repeat until all air is removed from the master cylinder.
   5. Tighten the brake line to 24 ft. lbs. (32 Nm) when finished.
   6. Repeat these steps for the right front brake line (rear upper port) at the master cylinder.
      

WARNING Do not allow brake fluid to spill on or come in contact with the vehicle' finish, as it will remove the paint. In case of a spill, immediately flush the area with water.

1. If a single line or fitting was the only hydraulic line disconnected, then only the caliper(s) or wheel cylinder(s) affected by that line must be bled. If the master cylinder required bleeding, then all calipers and wheel cylinders must be bled in the proper sequence:
   1. Right rear
   2. Left front
   3. Left rear
   4. Right front
2. Bleed the individual calipers or wheel cylinders as follows:
   1. Place a suitable wrench over the bleeder screw and attach a clear plastic hose over the screw end.
   2. Submerge the other end in a transparent container of brake fluid.
   3. Loosen the bleed screw, then have an assistant apply the brake pedal slowly and hold it down. Close the bleed screw, then release the brake pedal. Repeat the sequence until all air is expelled from the caliper or cylinder.
   4. When finished, tighten the bleed screw to 97 inch lbs. (11 Nm) for the front, or 66 inch lbs. (7.5 Nm) for the rear.
3. Check the pedal for a hard feeling with the engine not running. If the pedal is soft, repeat the bleeding procedure until a firm pedal is obtained.

Fig. 1: Loosen the front brake line in order to bleed the master cylinder

Fig. 2: Connect a bleed hose from the bleed valve on the front caliper to a jar of brake fluid

Fig. 3: Always follow the lettered sequence when bleeding the hydraulic brake system

Hope this helps to solve it; remember to rate this answer.

sometimes if you leave the bleeder screw open it will gravity bleed the cylinder.Make sure master cyl is full and do one wheel at a time.I have seen this work, I have done it.

Brother, it's just the fact that there is STILL air in your system. Just fill the master cylinder, open the left front line and let it run into a bottle to catch it for a bit until you know for sure all air is gone from that line. Then do the same with the right front. Then the left rear, then right rear. This is gravity bleeding, no pumping required. It's the only way to know for sure that each wheel cylinder and line is free of air. Only let the master cylinder drain down about half way each time the tighten each bleeder. Refill with the drained fluid. Be patient my friend, it takes time to do it right, but it works for me every time. Good day.

did you bench bled master? if yes do you have abs system,if so you must bleed at abs block,if it has bleeders, if not then you must line bleed all 6 lines.2in from master 4 out to wheeles. then rebleed wheel in cylinder.If you have bleeders at abs block you dont to rebleed wheels. best dun with powerbleeder. hoooooops this helps

The piston is binding in the wheel brake cylinder, perhaps a bit of rust in the cylinder.
Inspect it, replace wheel brake piston and maybe the cylinder if you can't make it "smooth".

start by bleeding the master cylinder bleed the line closest to the fire wall, then proceed to the right rear wheel, left rear wheel, right front wheel, and then the left front wheel.

Hello,
I hope this helps.







Thank You,
Roy

Brake Lines and Hoses
Double-walled steel line is used in the hydraulic lines between the brake master cylinder and the front tube connector, and between the brake master cylinder and the flexible brake hose at the rear wheels.
Double-flared brake lines provide good leak-proof connections.
When replacing hydraulic brake lines, hoses, or connectors, tighten all connections securely. After replacement, bleed the brake system; refer to Section 206-00 .
The wet appearance of the outer cover of the rubber brake hose is referred to as "sweating." This is a normal condition for neoprene rayon braid hose and is not a sign of leakage or cause for replacement of the hose.

Hydraulic Brake System Components — Non-ABS


Item Part Number Description 1 2005 Power Brake Booster 2 2455 Brake Pedal 3 2261 Rear Wheel Cylinder 4 2552 Rear Disc Brake Caliper— (Mexico Only) 5 2B120 Disc Brake Caliper—, Front 6 2B091 Brake Pressure Control Valves 7 2140 Brake Master Cylinder