Question about Mitsubishi Eclipse

1 Answer

I got a 1995 Mitsubishi eclipse with a turbo in it. I got the diagnostics ran on it and it read the po300 code. Just before it, i got the alternator replaced. Not sure what is wrong with it now. But it idles really low and seems like it doesnt have enough power to move at some points..

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

P0300 - random misfire detected.

Your could have a single coil with distributor cap or just coil packs, came both ways that year, check spark plug's and spark plug wire's, if it has a distributor cap, check it and the rotor also, not bad idea to do a cylinder compression test, this was you know the condition of the engine cylinder, all cylinder's should be about the same compression, give or take about 10% of the reading, hope this was very helpful.

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1995 elcipse gsx turbo awd transaxel will not engage when driving and switches gears alone what could be the problem it also sometines will not start right away. can any one help me


Hi there,

You (or someone technically inclined) can extract your diagnostic codes from your vehicle's transmission computer by jumping pin no's 1 & 4 on your diagnostic connector (located above your knee, under the dash). Note: this connector may be mounted upside down (but the long edge has pins 1-8).


wolfman304_6.jpg

The transmission codes are read by way of observing the flashing "N" light (i.e. the gear selector light on your instrument panel).

* Long flash = 1st digit of code
* Short flash = 2nd digit of code

Note: continuous flashing (i.e. no sequence) means NO fault codes present.

If codes are present, they will repeat over, giving you time to record the codes.

Also, if any of your other warning lights (e.g. Engine or ABS) appear to flash a code, note these also.

Write down your codes and report back here - I will advise what the codes mean.


Await your response....

Cheers,

Jul 24, 2011 | 1995 Mitsubishi Eclipse

1 Answer

MAP sensor Location


Its located on the intake manifold near the goooseneck

Jan 17, 2010 | 1995 Mitsubishi Eclipse

1 Answer

Won't start


I recently had this problem with a supercharger and it was actually that extra belt that controls the supercharger (hopefully in your case turbo)the pully actually broke that may be your problem their fairly cheap to replace and re install

Dec 29, 2009 | 1995 Mitsubishi Eclipse

1 Answer

Checking codes


there isnt a way but all autozones and advanced auto parts stores does it for free

May 01, 2009 | 1995 Mitsubishi Eclipse

1 Answer

Codes for 1995 Mitsubishi eclipse


Engine-light-help.com

P1100 Induction Control Motor Position Sensor Fault

P1101 Traction Control Vacuum Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1102 Traction Control Ventilation Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1103 Turbocharger Wastegate Actuator

P1104 Turbocharger Wastegate Solenoid

P1105 Fuel Pressure Solenoid

P1294 Target Idle Speed Not Reached

P1295 No 5 Volt Supply To TP Sensor

P1296 No 5 Volt Supply To MAP Sensor

P1297 No Charge In MAP From Start To Run

P1300 Ignition Timing Adjustment Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1390 Timing Belt Skipped One Tooth Or More

P1391 Intermittent Loss Of CMP Or CKP Sensor Signals - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1400 Manifold Differential Pressure Sensor Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1443 EVAP Purge Control Solenoid '2' Circuit Fault

P1486 EVAP Leak Monitor Pinched Hose Detected

P1487 High Speed Radiator Fan Control Relay Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1489 High Speed Condenser Fan Control Relay Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1490 Low Speed Fan Control Relay Fault

P1492 Battery Temperature Sensor High Voltage

P1494 EVAP Ventilation Switch Or Mechanical Fault

P1495 EVAP Ventilation Solenoid Circuit Fault

P1496 5 Volt Supply Output Too Low

P1500 Alternator FR Terminal Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1600 Serial Communication Link

P1696 PCM Failure EEPROM Write Denied

P1698 No CCD Messages From TCM

P1715 Pulse Generator Assembly

P1750 Solenoid Assembly

P1791 PCM ECT Level Signal To TCM Circuit Fault

P1899 P/N Position/Transaxle Range Switch Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1751 A/T Control Relay

P1791 Engine Coolant Temperature Level Input Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1795 Throttle Position Input Circuit To TCM - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

Mar 21, 2009 | 1995 Mitsubishi Eclipse

1 Answer

Self diagnostic test codes


anytime you do the self-diagnostic you will almost always get those 2 codes.

12 - direct power input to the PCM has been disconnected within the last 50 key-on cycles

55 - End of error messages

Dec 27, 2008 | 1997 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...