Question about Volvo S80

1 Answer

CAN YOU TELL ME HOW TO PUT ON CHEMICAL GASKET AND HOW LONG WILL IT TAKE TO SET UP?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 972 Answers

Its applied with a fine foam rubber paint roller, the type used for stains/or clear finish.it will never set up until assembled.it anerobic and wont cure untill its in an oxegen free enviroment.can use car right after assembly

Posted on Sep 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much patio cleaner do I need to put in the bottle


Read the instructions on the Patio cleaner chemical. It has to tell you by law.

Mar 17, 2017 | Cars & Trucks

1 Answer

My 2002 mazda 1.6 protege over heats I put thermostat new radiator what could be wrong now


it could be a head gasket which can be tested with a chemical test or a bad water pump. make sure the rad cooling fan is working this will cause over heating if not working.

Aug 25, 2014 | Cars & Trucks

1 Answer

Signs blown head gasket


There's a hydrocarbon test you can do at home or some radiator shops can do it. The kit is sold at a "Real" auto part store like NAPA, I doubt Auto Zone, Pep Boys or O'Reilly's would have these. You pull a little water/antifreeze from your radiator and put a few drops of the supplied chemical in it. It will tell if there's hydrocarbons in it. There should be no hydrocarbons in your radiator. I hope this helps

Jun 17, 2013 | Chevrolet Cars & Trucks

1 Answer

Radiator flush and replacement


Flushing you can add the Chemical and follow the Directions on the Bottle

Thermostat is 3 bolts, clean the housing, install the new gasket and tighten it down

Make sure you put the Pill DOWN

Apr 10, 2013 | 1993 Toyota 4Runner

1 Answer

I have an Audi 90 1995. There is an oil leak behind the water/oil heat exchanger. I put in a new gasket but still a slight leak. What's the fix? Thanks.


basically check the surfaces are flat...pull the heat exchanger off and run a metal ruler or square across them, if there out gently run a flat file over them, if not put some silicone based chemical gasket around there and should take it up, good luck :)

Jun 28, 2011 | 1995 Audi 90

1 Answer

I want to learn how to put a head gasket set on a 96 buick riviera


Why would you want to put a head gasket on one. They hardly ever go bad on a 3800 engine. Worked at a buick dealer for many years and only have seen one that was leaking but it was not original gasket. Tell me the symptoms and I will guide you through it. Super charged motor or not? Please reply

Jan 15, 2011 | Buick Riviera Cars & Trucks

1 Answer

I am planing to change the head gasket of my 98 vovlo s70, it gets over heat very quickly. can i know if there are special precautions while dis assemblin and assemblin. Can som one tell the torque specs...


before you start taking it to bits have you checked thermostat is opening ok and that radiator is not blocked also that the cooling fans are working a chemical test or sniff test can be done to check for gases in cooling system these engines are strong not prone to head gasket problems

Dec 04, 2009 | 1998 Volvo S70

1 Answer

Only 750 miles on scooter. Put away with stabilizer. Starts bar-o-o-m like it's going to run fine. Then stops and won't start. Checked plug and spark. Plugged line?


The stabilizer is a bad thing for some carbs. It has a chemical in it that can eat away seals and gaskets inside your carb. Grab a gasket set for it, replace those, make sure to spray the carb out, then put it all back together adn you should be ok.

May 07, 2009 | Honda CR-V Cars & Trucks

1 Answer

Head gasket


The best solution? Remove the heads, have them planed to true them up and put new gasket set on. Depending on how many miles the engine has on it, it may be needful to have the heads reworked. New valves guides, the valves ground and seated. If it has a lot of miles it could be best to purchase a set of remanufactured heads. If the engine is low miles a gasket set and planing the head will probably do it. If you just have one head plane, make sure to get the proper gasket for that head. The planed head will cause that bank of cylinders to have higher compression then the other non-planed side. You will have to get a thicker gasket for that side to keep the same compression. Your machine shop can tell you how much they took off. Hope that helps.

Jul 30, 2008 | 1991 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...