Question about 1994 Chrysler LHS

1 Answer

I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 157 Answers

These are the steps you need to follow for this procedure if you have the proper tools.

  1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
  2. Remove hub and bearing to stub axle retaining nut.
  3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
  4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
  5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

Posted on Aug 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 95 lhs which was given too me... it was drove back too ca from tn and messed up when it got here... it will start up but it shakes and dies and blows out white smoke.... would u think it would be...


hi.
white smoke would suggest the head gasket is blown and the smoke and the shaking and dying would be caused by coolant getting into one or more pistons and burning with the petrol.
at the very least you would need to replace the gasket and get the head skimmed.
you would also have to find out if there was an underlying problem that may have caused the gasket to blow in the first place and allow a budget to fix any remaining issues after the gasket has been repaired.

Feb 25, 2011 | 1994 Chrysler LHS

1 Answer

DIAGRAM ON HOW TO CHANGE A WATER PUMP IN A 1994 CHRYSLER LHS 3.5


You first off have to take the belts off the front of the engine Then take off the front covers and the external belt tensioner then inside there is the water pump You will have to drain your antifreeze then remove the timing belt You might as well replace this part too

Nov 20, 2010 | 1994 Chrysler LHS

2 Answers

1997 chrysler lhs question; there is grinding in the front end


I would check the front brake pads. Also, check the front wheel bearings.

Oct 22, 2010 | 1997 Chrysler LHS

1 Answer

My chrysler Lhs is overheating and leaking coolant from the front. I already replaced the water pump. What can it be?


check all your hoses. check to make sure the fans are turning on. was the thermostat replaced as well?

Jul 13, 2010 | 1994 Chrysler LHS

1 Answer

ABS light is on all the time as well as Traction Control light. Grinding occurs while driving


with traction control set up cars abs and tranction control sensors are in the wheel bearings when a wheel bearing goes out grinding will come from front wheels and will ruin abs and traction control sensors causing the malfunction. Most likely by your description this will be it.

Mar 18, 2010 | 1996 Chrysler LHS

2 Answers

In a 94' Chrysler LHS what is the firing order? Took the plug wires off the housing unit.


1994 Chrysler LHS
3.5 liter SOHC V-6 VIN "F"56539136.gifI HOPE THIS IS WHAT YOU NEED. THANKS FOR USING FIX-YA. PLEASE KEEP ME POSTED. FEEL FREE TO COMMENT ON THE ASSISTANCE

Sep 06, 2009 | 1994 Chrysler LHS

1 Answer

1994 LHS STEERING BROKE - WHEEL FREELY SPINS


First thing I would check is the inner tie rod bushing, common failure on Chrysler products.

Feb 09, 2009 | 1994 Chrysler LHS

Not finding what you are looking for?
1994 Chrysler LHS Logo

Related Topics:

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...