Question about 1994 Isuzu Rodeo

1 Answer

No injector pulse, Gas pump has been replaced theres gas in rails , theres sparks will fire with starting fluid have changed ecm. please help

Posted by on

  • Aki Aug 27, 2010

    What Engine Size?

  • chkreloaded Aug 27, 2010

    its not a rhodeo is a crown vic lx 2000 4.6 dont know why it put it as a rhodeo after i change.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 157 Answers

Check the Camshaft Sensor and the Crankshaft sensor

Posted on Aug 27, 2010

  • chkreloaded Aug 27, 2010

    ok i sure will ill respond with the results

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel injector relay on a 2004 vw gti 2.8 liter 24 valve 6 cylinder?


check the immobilizer as it may be preventing the ECM to allow fuel past the injectors
run the fault codes and it could be the ECM needs resetting using a scan tool

Mar 13, 2016 | Cars & Trucks

1 Answer

1990 eighty eight 3.8l. Why no fire/pulse to the injectors?


The camshaft sensor may be bad. Check the fuse for the injectors and it is possible the ECM is bad or the injector drivers more specifically are bad in the ECM .

Nov 24, 2015 | Oldsmobile Cars & Trucks

2 Answers

Will fuel pressure regulator stop engine from starting


Yes it can if it can't maintain the correct fuel pressure. I would also check that the injectors are getting a signal from the ECM.

Feb 07, 2015 | 2003 Buick Century

1 Answer

No injector pulse on daihatsu feroza


injector pulse is just controlled by the ecm or computer as some would say,u said u replaced wires? did u have a fire or melt wires? ecm is known to go bad on these,had a few of these trucks back in the day.

Oct 05, 2012 | Cars & Trucks

2 Answers

My 1995 corvette coupe will not start; it has gasoline, a good battery and turns over good but the engine will not fire; when it does (on occassion) the engine is rough running and will die. The optic...


Check your voltage to the fuel injectors.Also check to see if the fuel injectors need cleaning.First, put your fuel pressure gauge on the shrader valve on the end of the right fuel rail. You should have 35-42 psi and it should hold up for a long time with the ignition turned off. The signal to the injectors is a pulse to ground on the green/blk wire of each injector. The black wire on the injector goes to 12v. Get a noid light at a parts store and see if your injectors are being pulsed during cranking. If not, first check both injector fuses with an ohmeter, they see a lot better than you do. If you have a pulse and fuel pressure and still no starting, you have contaminated gasoline. Engines that start on starting fluid have no gasoline/air mix in the intake due to no gas, or no injecting.Even a cheap $5 multi-meter will work for you.
Check for +12 volts at the black wire of each injector connector or check continunity between all of them and then for +12V.

Check for continunity between the green/black wire and at the ECM connector. Take the connector off the ECM to get at the pin. Also disconnect the neg battery cable before doing this one.

Aug 04, 2017 | 1995 Chevrolet Corvette

2 Answers

Try to start truck but battery dies.


check your ground wires. its quite common that they rust off and then that causes a no start. check along the frame by the battery, and starter.

Apr 10, 2010 | 1997 Dodge Ram 1500 Club Cab

1 Answer

No gas coming out the injector and there is gas pressure to the injector?


Is there an injector pulse going to the injector?(an electrical pulse to fire the injector).
Is there spark at the plugs?
If the pickup in the dist is faulty you won't have either one.
If your vehicle uses a crank pickup with or instead of dist pick up....if it is defective ....no pulse.
The above is 90% cause of no pulse....other is computer problem 10%.
If you do have a injector pulse and no spray.....and have fuel pressure....change the injector.
A quick check for spark is spray a little starting fluid in it.....if it starts on the fluid....spark is present.

Nov 03, 2009 | 1997 Chevrolet Blazer

2 Answers

Crank no start: has no spark and only has injector pulse on cyl # 1. if you spray starting fluid directly into throttle body car starts and stays running and has spark and inj. pulse. once you turn the car...


Fuel pump, you have to have press in the rail to fire all injectors- she will run on ether but not good for her. Ck your pump and any related fuses,relays,wiring.

Jul 11, 2009 | 2002 Hyundai Accent

1 Answer

Will run cold shut off at temp and will not start back up


Replace or Check the gas cap. To much suction might be causing it to cut out.

Jmac

Mar 24, 2009 | 2002 Pontiac Firebird

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...