Question about Toyota Corolla

1 Answer

I was installing HID lights into a 99 corolla when plugging in the drivers side light I may have plugged the wires into the socket incorrectly. Now the left side does not work even if I plug in a regular halogen bulb. The passenger side works fine. I swapped out the bulbs from left to right side and nothing. Everything I plug in on the passenger side works and nothing I plug into the drivers side works. I checked the fuses for both RT and LT and they are fine, I even swapped them to make sure. Why isn't my drivers side headlight working ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 9,587 Answers

The contacts in the headlight relay have probably burned. Try swapping the relay with an adjacent one to see if that fixes the problem

Posted on Jun 27, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

66 chrgr
  • 1011 Answers

SOURCE: Right side headlight (low beam) dead

clearly volts without amps. pinch wire bad socket or multifunction switch under cover on steering column.

Posted on Jan 25, 2009

  • 383 Answers

SOURCE: 2001 subaru outback headlight not working

chapmnfarm: your head lights use a "2" fuse system.
one for the left and one for the right.
The fuse box you are looking for is under the hood on the passenger's side. It is a black box roughly 8 inches long and 4-5 inches wide. When you remove the cover, you will see fuses and relays. What you are looking for is the section in the box which has a cluster of 7 fuses. 3 in one row and 4 in the other. On the outer parameter are two relays. The fuses you are interested in are located in the row of 4 fuses, with the two closest to the "L" shaped part of the box. Both of those should be 15 amp fuses.
The fuse below those should be a 20 amp which is the lighting switch and the one below it is a 15 amp which is for the interior lights and the clock.
Check your harness grounds in the engine compartment near the area you have the problem. There are ground wires which come out of the harness on both sides of the core support. The wires are black in color and have "EYES" crimped onto the ends of the wires. Both of them will probably be located about 4-6 inches below the upper tie bar on each side of the radiator. Odds are that the eyes will be large enough to pass a 6mm bolt through.
I hope what I have given you will resolve your problem. Lem me know,,good luck>>>>>>>>>>>>>>>

Posted on Apr 19, 2009

  • 18 Answers

SOURCE: 2004 IS 300 - does it have HID or Halogen low beam lightbulbs?

Your low beam is a HID bulb, number D2R, and your high beam is a halogen 9005 bulb

Posted on Jul 27, 2009

  • 1244 Answers

SOURCE: theres a bar that ext from the fr rt to the ft lt

stabilzer bar

Posted on Jan 14, 2010

  • 2 Answers

SOURCE: I have a 2004 Nissan

It sounds like you have wire problem. This problem can be manny problems from a short due to exposed wire or it is broken somewhere... ect. if it is not the wire check further back the line to see if the buse is recieving power. Or it could be as simple as the plug you put the bulb in has a broken contact tip

Posted on Mar 29, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace front HID light bulb? and where can I purchase parts for replacing?




  1. INSTALLATION GUIDE:


  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights


  3. Parts Identification:


  4. Projector Headlight


  5. Halo & L.E.D.


  6. Bottom of the Headlight:


  7. Ballast Bracket, Halo Wires(red/black)


  8. Turn Signal Adaptor


  9. TOOLS REQUIRE


  10. 10mm - 8mm socket


  11. Philip Screwdriver


  12. Crimper/Pliers


  13. For more information about how to install your vehicle, come visit our youtube page on


  14. http://www.youtube.com/spyderauto


  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.


  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.


  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.


  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.


  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.


  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.


  21. STEP:


  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.


  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.


  24. Factory Xenon Headlight


  25. Spyder Projector Headlight using Factory Xenon Lights






replace-front-hid-light-bulb-purchase-afy5cnsznmokzumyhdcbeseq-5-0.jpg

May 21, 2014 | BMW 335i Cars & Trucks

2 Answers

I have problem with hid light


follow this link to u-tube video not the exact vehicle but the principle will be the same,or search for your exact vehicle
How to replace low beam xenon HID bulbs 2006 BMW 330i

May 08, 2014 | 2007 BMW 335i Coupe

1 Answer

HEADLIGHTS DO NOT WORK, BUT HIGH BEAMS DO AND SO DO TURN SIGNALS AND SIDE MARKERS


The HID requires a ballast, did you do any rewiring? Did you check the fuses? Unplug the relay either hi or low, use jumper wire between terminals 30 and 87, the lamps should work, I'm talking about your regular lamps. If they work with the jumper, then check control side of relay.

malibu headlamps-n3gdy1s0yelmttnhr2yepr4t-2-0.jpg

Mar 06, 2017 | 2009 Chevrolet Malibu

1 Answer

Head Lights Don't Work But Hi Beams, Turn Signals, And Side Markers Do


Have you check all the fuses with a volt meter and also there should be fuses under the bonnet. Is there a volt supply on the wires that you replaced just to make shaw that the wires haven't melted down the wiring loom i know on most newer cars each light has its own fuse ,is all the rear lights working ok .if you let me know what make of car you have i will see if i can find any thing out for you,
the other problem could be your light switch inside the car thats burnt out i had this problem with my ford sierra cosworth one minute it was ok then went to go home and i didnt have any lights.
hope this helps.puggy

Jan 11, 2014 | Chevrolet Malibu Cars & Trucks

2 Answers

My right side headlight not working on A4, 2007. Install new H7 bulb from Audi but it did not work. I install the right bulb into the drivers side and it work. I suspect an electrical problem. Possible no...


if it is a hid light system they are famous for the balast going bad. follow the wires from light bulb. if they go into a box then its a hid system and it is the balast box that needs to be replaced. also check the fuses, sometimes there are seperate fuses for each headlight.

Mar 09, 2013 | Cars & Trucks

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

2 Answers

Lt. headlight low beam wont work after replacing the bulb.


I assume it didn't work before you changed the bulb either. You'll have to check for voltage at the bulb socket when the low beam headlights are turned on. If there is none you'll have to trace the wire back to where it splits from the right low beam headlight. If there is voltage there you have a problem with the new bulb.

Apr 10, 2011 | 1991 Lexus LS 400

2 Answers

How do you change front headlight blub 2008 sonata


how do you change front headlight blub 2008 sonata

Nov 28, 2009 | 2008 Hyundai Sonata

2 Answers

How to install hid on a bmw 325xi 2006


INSTALLATION GUIDE:
BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
Parts Identification:
Projector Headlight
Halo & L.E.D.
Bottom of the Headlight:
Ballast Bracket, Halo Wires(red/black)
Turn Signal Adaptor
TOOLS REQUIRE
10mm - 8mm socket
Philip Screwdriver
Crimper/Pliers
For more information about how to install your vehicle, come visit our youtube page on
http://www.youtube.com/spyderauto
Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
STEP:
Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
Factory Xenon Headlight
Spyder Projector Headlight using Factory Xenon Lights
STEP:
pls vote an diam giving you link also for better help BMW e46 HID Headlight Replace
install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-0.jpg

install-hid-bmw-325xi-2006-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Oct 15, 2009 | 2003 BMW 325

1 Answer

Corolla 2002 backup light problem


I'd backtrack with test light from socket with low voltage reading. If you probe behind socket, or wire going into socket for power, and it shows bright, you've isolated problem area.

Mar 01, 2009 | 2002 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...