Question about Chevrolet C1500

1 Answer

I have a 1969 chevy step side and i cant get my back tail lights to work any ideas,myturn signals work but the tal and running lights wont.thank you

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Contributor
  • 157 Answers

Have you looked into the Light Switch for that part of the circuit, check to see that when in fact you do switch the headlights on there is power distributed out of it, ALSO , check at the actual light sockets in the back and see if u have power and ground present if either is not there you will have to trace it back till you find your loss. Check Fuses 1st off its the fastest way to make certain you will have power present to light switch. Also check connections sometimes the older vehicles get rust at the connectors and loose conductivity

Posted on Aug 27, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 buick lesabre tail light on left side does not work but the brake and turn signal works.


you need a new bulb the one bulb for the tal light and break has two filaments and one is fryed

Sep 11, 2013 | Cars & Trucks

1 Answer

Left turn signal quit working. 1969 chevy pickup-


sounds like you have a bad flasher which is usually located near the steering column under the dash. check for ground on front left bulb. may have to replace light socket if ground is good.please leave comment.

Mar 20, 2010 | 1983 Chevrolet K1500

2 Answers

No signal lights at all and no emergency flashers


you need to check the "combination turn signal/hazard flasher/daytime running lights module"
it is located in the junction block,the junction block is adjacent to and left of the steering column,you need to remove the lower dash panel below the steering column,then remove the steel knee brace.

Dec 31, 2009 | 1996 Plymouth Voyager

1 Answer

Tail lights dont work


Oh boy, Chevy uses 3 important wires to make up their tail light harness. Brown is used for your parking lights and yellow and green are your signal and brake light wires, yellow one side, green the other. You have some seriously crossed wires. Start with tracing the lic plate lite since that works. Make sure it leads into your main parking lights and the ground wires from these tail lites aren't cut. The lic place lite will work with just power because the body of the lite is grounded with the bumper. Then make sure that there is power to the signal wires. You can do this with a test light and the signal light switched on. You don't need anyone to step on the brakes since it's the same signal, only interepted. Most importantly, Remove the tail lites and check grounds!! Good luck

Jul 02, 2009 | 1991 Chevrolet C1500

1 Answer

No Brake Lights 1993 Chevy Astro Van


Check the ground wire & leads, if not try the multi-function switch in the column

May 29, 2009 | 1993 Chevrolet Astro

2 Answers

1969 ford mustang mach 1 brake / stop light switch challenge


Most tail light problems are a result of a bad ground......somewhere.

Sep 16, 2008 | 1966 Ford Mustang

1 Answer

Chevy venture


Solution to your problem ... 1- I purchased from 1aauto.com a pair of Circuit Boards for my Chevy Venture 2003 for 85.00 $ ..free shipping 2 - I Installed them both , all lights now were not working at all. So I checked them and they were all burned ...So I purchased new ones ....Everything was working fine now but now my signal lights were not working left and right .....Checked the fuse box next to the passenger side door .... It was burned . Changed the fuse / Signals are working fine now ....All is good I just did this yesterday evening August 12, 2008 Conclusion ..Change everything going forward so you do not need to run around like I did from one store to another!
  1. Circuit Board : New
  2. Bulbs : New
  3. Fuses : New
Thank you

Jun 26, 2008 | 2003 Chevrolet Venture Passanger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...