Question about 1995 Ford Contour

1 Answer

Trans disengages while driving then it will feels like it wants to come thru the floor when it engages it self

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

The first thing to do is check the fluid and level of fluid and if it is burned I recommend to go to a transmission shop for further diagnosis and repair or replacement

Posted on Aug 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No forward engagement in drive position


If engine revs go high and no forward movement you most likely need a new transmission

Jul 11, 2017 | 1999 Ford Contour

1 Answer

4wheel drive will not go into any gears 5speed


do you mean the 5 speed manual transmission will not go into gear? and it is a 4x4 truck? I would check clutch linkage and fork or slave cylinder if it applies to this model. Is it grinding at all? Can you determine if the pressure plate is actually disengaging the cluch plate. If the pressure plate is properly disengaging then the problem may be the shift fork in trans is broke,wedged. trans mainshaft broke, I'm not sure but does that year have a removable floor pan cover under floor mat above trans? AS you can pull the top off trans and inspect without pulling trans out of truck.

Feb 08, 2011 | 1995 GMC Sierra C1500

2 Answers

Not sure if shifter is installed properly


Ok, I guess its going to be a not too obvious solution then. All we have to do is find it...
1.What type of gear shifter is in your truck. Column or tower
2. Is the tail shaft turning when you try to move the vehicle
3. Does the vehicle try to move at all
4. Is there any noise from the gearbox or clutch area
5. Are you certain the clutch kit was the right one
6. Did you try the clutch plate on the gearbox input shaft spline
7. Is the release bearing clear of the pressure plate fingers.
8. Does the release bearing carrier slide freely on the retainer on the front of the bearbox, and did you apply lubricant here.

Mar 26, 2010 | 1987 Ford Ranger

1 Answer

1995 GMC P-UP 4 wheel drive will not engage. Worked fine last night, got up this morning and it would not engage. This model GMC has the manual shift in the floor.


Drive forward, put it in neutral, the into reverse. If you have not used the 4wd for awhile it will need vacuum to activate and disengage

Dec 19, 2009 | 1995 GMC Sierra C1500

2 Answers

Transmission


F4AEL trans,old mazda design.Many possible causes across a broad spectrum from low line pressure,bad torque convertor,to electrical solenoid failure,and even internal transmission failure.All systems involved with the trans have to be checked and evaluated.Main line pressure can be checked with a mechanical gauge,trouble codes pulled from the vehicle to determine any possible problem with the trans electronics from shift solenoids to speed sensors.Pan contents and fluid condition also a factor in the final diagnosis.A complete under car check to verify the drive axles are fully engaged into the trans.I also have at work a Zoom Technologies box,some call a breakout box,that allows complete manual control of the trans,eliminating the vehicle computer from the picture.This is to isolate the trans from it's control system,and verify the problem is indeed with the trans,and not the computer.Sophisticated,expensive equipment is really needed to diagnose properly,including a scan tool,and breakout box,and a source like All Data online to run down,diagnose,and repair trouble codes.

Sep 02, 2008 | 2003 Kia Rio

Not finding what you are looking for?
1995 Ford Contour Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...