Question about 1999 Jeep Grand Cherokee

Open Question

Where is the oil pressure sending unit location on my 4.0 1999 jeep cherakee

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: where is the oil sending unit switch located on a


Removal & Installation

  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
7f7455b.jpg
To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Posted on Oct 08, 2009

  • 101 Answers

SOURCE: 2002 Jeep Grand Cherokee 4.0L oil pressure gauge reading too high

if the gauge starts a 0 - goes to 1/2 , than full - sounds like gauge is OK - seems to me like the sending unit is bad - you could try removing the sender and trying to clean out the port with "brake clean", letting it dry than re-installing it. the pressure switch is still the least expensive place to start

Posted on Oct 27, 2009

techbuster
  • 5081 Answers

SOURCE: Exactly where is oil pressure sending unit located

if you have the 5.2 V8 its located in the rear of the engine near the dist cap area you can see it if you look in that area , if 4.0 6 cyl its located on the side of the engine block near the oil filter area. It has two wires going to it and screws into the block. It's made mainly of plastic and if broken can allow oil under pressure to spew out and give you thoughts of a blown rear main seal due to the amount of oil all over the underside.

Posted on Dec 09, 2009

c17hydro
  • 2984 Answers

SOURCE: Where is the oil pressure sending unit located on

Removal & Installation

  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Posted on Jan 12, 2010

  • 17 Answers

SOURCE: how to change oil pressure sending unit on jeep

First things first do you have a repair manual? If you don't have one get one, Changing the unit is realitively simple, you just disconnect the battery, disconnect the oil pressure sending unit's electrical connector, remove the sending unit, now most sending units are small and look like a short chubby spark plug with an electrical blade connector on the end of it. simply use a wrench to loosin and remove and install by screwing in and tightening and reconnecting the electrical connecter then the battery and your as good as new!

Posted on Feb 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 jeep grand cherrokee location of oil pressure sending unit switch 4.7 l engine


its next to filter. the sender fits to the main oil gallery
like the filter too.
why not just look at the dealer parts page, find it and see.
the fsm covers this too.
page 4804 (posted many times now)


25586465-cuky5fb52wfczksibethvkr1-3-0.jpg

Mar 17, 2015 | 2005 Jeep Grand Cherokee

1 Answer

Oil pressure drops to zero at idle. Check engine light comes on. Codes are 11,12,54. Had crank and cam sensors replaced. Wants to die when problem occurs. restarts easy. Do not hear engine clatter when...


Locate the oil pressure sending unit and get a pressure test for yourself. If it is okay, replace oil pressure sending unit. If the pressure is 0. Replace the oil pump. Probably not 0 because engine would seize.

Jun 14, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

Where exactly is the Oil Pressure Sending Unit on a Jeep Wrangler 2000 6cyl so i can replace?


Oil Pressure Sensor The 3 wire, solid-state engine oil pressure sensor (sending unit) is located in an engine oil pressure gallery.

Aug 07, 2010 | 2002 Jeep Wrangler

1 Answer

Where is the oil pressure sending unit located on a 2000 jeep grand cherokee 4.0 liter


Removal & Installation
  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Jan 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Where is the oil sending unit switch located on a 2003 4.0L jeep grand cherokee?



Removal & Installation

  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
7f7455b.jpg
To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Oct 08, 2009 | 2004 Jeep Grand Cherokee

1 Answer

No oil pressure


Sounds like sending unit, should be located by where the oil filter is.

Feb 26, 2009 | 1996 Jeep Grand Cherokee

3 Answers

OIL PRESSURE SENDING UNIT ON MY JEEP CHEROKEE 1993 WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT


OIL PRESSURE SENDING UNIT ON MY JEEP GRAND CHEROKEE LAREDO 1999
WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT

ANY SPECIAL KNOWLEDGE TO PUT IN?

Jul 30, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7689 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...