Question about 1993 Chevrolet Cavalier

1 Answer

What is the torque spec for the transmission pan bolts of a 93 chevy cavalier so i don't ruin the new gaskit

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

15 foot pounds

Posted on Aug 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the transmission gasket on a 1988 chevy Silverado


Raise vehicle and support on jack stands. Loosing nuts on transmission making one side lower than the other this will allow you to drain fluid. Drain fluid remove bolts on pan. Remove pan remove old gasket, clean pan and transmission edge, replace with new gasket. Replace pan and bolts. Torque to spec and refill transmission

May 05, 2016 | Cars & Trucks

1 Answer

How to replace oil pan gasket dodge caravan 2005 3.3l


jack up on jack stands, drain oil, remove all pan bolts, clean pan, use new gasket, replace bolts to torque specs do not over tighten it will tear the gasket. DO NOT USE GASKET SEALER OR PERMATEX IT MAKES GASKET SLIP

Mar 09, 2015 | 2005 Dodge Caravan

1 Answer

I have a 2002 mercury cougar V6 automatic and I know what the problem is. My car needs to have the transmission pan taken out and replaced along with the gasket. My dad and I want to fix it ourselves but...


easy job. Just loosen pan bolts enough to let the fluid start draining from one end. As more drains, keep loosening the pan bolts till you can remove pan and finish draining what's left in the pan. At this time, most people would also change the transmission filter body: it's right on bottom of trans. when the pan is removed, easily accesible. Parts stores sell a kit with new filter and pan gasket included. Anyway, now you are ready to install new pan gasket. Clean gasket mating surfaces as clean as you possibly can. let no oil or fluid get back on there. Place gasket on (most don't recommend adding sealant or gasket compound). Put pan on with all bolts fingertight. Then starting from center outward, start tightening them down to torque specs-it'd be pretty light torque, like around 20 ft-lbs-might want to ask a ford mech. what torque specs are. When done, refill ****** and check for leaks after running car.

Oct 14, 2011 | 1999 Mercury Cougar

1 Answer

Engine torque specs for 1996 chevy cavalier 2.2l


For 1996 Chevrolet Cavalier 2.2L SFI OHV 4cyl the check the next Head Bolt Torque sequence...

------------ front | 8 4 1 5 9 | of | | engine | 7 3 2 6 10 | ------------

Step 1: torque long bolts 8,4,1,5, & 9 to 46 Ft/Lbs torque short bolts 7,3,2,6, & 10 to 43 Ft/Lbs
Step 2: torque all bolts an additional 90 degrees Recheck final torque in sequence

*** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Hope helps (remnember rated this).

Jul 15, 2010 | 1996 Chevrolet Cavalier

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

3 Answers

I just replaced the gasket of the transmission pan and still have a leak on my 1999 chevy suburban?


The leak is coming from the pan ??
Maybe the leak is traveling to the pan seal area from somewhere else ?
Did you scape off the stuck-on old gaskit on trani and pan ?
Its customary to use gaskit sealer on both sides of the new gaskit..

Aug 13, 2009 | 1999 Chevrolet Suburban

1 Answer

Where is the bolt to drain the transmission fluid on a honda element


Allot of trani pans have no bolt.. You would just drop the pan & fluid comes out..
Dont forget to get a new pan gaskit & a filter - if that model calls for one..

FYI; A pan drop is only part of the fluid - about 3 to 5 quarts..

The trani & torque converter hold 7 to 9 quarts all together..

Hope this helps !!
Rate me good ;o)

Jul 10, 2009 | 2008 Honda Element

2 Answers

Torque settings for transmission pan on 2000 chevy


Good rule of thumb is 15-18 inch lbs.More important is doing them evenly,like in an x type pattern.Good luck,
ChevRev

Mar 16, 2009 | 2000 Chevrolet Cavalier

Not finding what you are looking for?
1993 Chevrolet Cavalier Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...