Question about 1988 Mazda RX-7

1 Answer

Clutch is not engauging and wont go into gearr friends can help.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Check the clutch fluid, if empty fill and bleed clutch line, if its full check the clutch slave sylinder it might be seized, replace and repete steps

Posted on Aug 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 chevy K1500 and we replaced the fly wheel and now it wont go into gear.. HELP!


the most common fault is what you have stated
clutch plate in back to front
the clutch plate hub hits on the flywheel bolt heads and the plate is still driven making 1st and reverse gears difficult to select without crunching them

Feb 29, 2016 | Cars & Trucks

2 Answers

A friend grounded the power wire to my ignition on my 96 yzf600r and now it wont start I replaced the fuse and the lights come on but wont turn over please help


Check every switch,solinoid, and wires from the ignition connector to the starter, with a volt meter, follow the 12 volts from the start button to the starter to the battery.
On a wild guess, the starter solinoid doesn't have 12 volts coming out of it when it is engauged.

Best of luck!

May 03, 2015 | Cars & Trucks

1 Answer

Just had a/c motor put on an belt now transmission wont engauage


check the wiring for a dislodged wiring connector to the gear box. It will be that the torque converter clutch is not working from a lack of communication with the CPU and the TCM

Jan 19, 2014 | 1995 Nissan Maxima

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

2004 kia sedona ex ac not working can jump ac


You could have several problems. If your pressure readings (freon) are low it will not kick on the clutch for the compressor. Do you happen to know what your pressure readings are when you do jump it or what they are (low or high pressure side) when it isn't engauged? Also you could be dealing with a relay or a sensor that detects your pressure readings. Really knowing your pressure readings would be a start before I can begin to help.

Sep 03, 2013 | 2002 Kia Sedona

1 Answer

When engauged it wont lock in front wheels with the front jacked up it acts like a clutch is slipping in the tranfercase


It probably is the clutch used by the Auto-4WD mode. Excessive use of auto 4WD will burn up the clutch.

Will it work in 4HI?

Feb 07, 2011 | 2001 Chevrolet Suburban

1 Answer

It is like 2 sets of clutches are engauged


you didnt build it correctly....www.TransmissionGarage.com

Nov 05, 2009 | 1991 Chevrolet S-10 Blazer

2 Answers

A/C clutch will not engauge


i am not sure on this vehicle but it is usually right on the compressor..

Aug 01, 2009 | 1996 Chrysler LHS

1 Answer

Nissan Altima 1992 -AC clucth is not engauging after 10-12km .


Replace the A/C compressor if the Magnetic clutch is bad. You can try and take it apart to clean but you will never know for sure if it will bereliable. The system will have to be drained to replace. Also if it is not a R134a system you may have to have it converted. Seals and such replaced.

Jul 24, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
1988 Mazda RX-7 Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...