Question about 2004 Suzuki Forenza

1 Answer

Cam shaft sensor location - 2004 Suzuki Forenza

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 7 Answers

Hi, if you were looking down at your motor from above , and you pictured the engine as a clock with 6:00 pointing to the radiator, the camshaft position sensor would be under the plenum at 8:00. hope this helps.

Posted on Aug 26, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Nissan Altima crank shaft censor located bank 2


there is only one crankshaft sensor so you will be looking for a CAM shaft sensor for it to be on bank 2
go google and type in --location of cam shaft sensors on nissan altima engine ---

Dec 18, 2016 | Nissan Cars & Trucks

Tip

CMP - Cam shaft Position Sensor


<p><b><span>3.2) <span> </span><u>CMP - Cam shaft Position </u>(sensor)<u> </u></span></b><br /> <p><b><u><br /></u></b><br /> <p><b><span>What is it?</span></b><span><span> </span>This electrical device is very similar in concept to the crank position sensor (above) in that it detects the position of the rotation of a shaft, in this instance the cam shaft.<span> </span>It is the cam shaft signal that indicates to the ECU that cylinder one is at top dead centre at compression and in the process provides the ECU with the timing reference for fuel injection.<span> </span>The cam shaft sensor provides extra information, to that of the crank sensor, to fine tune timed events such as injection and spark delivery.</span><br /> <p><span> </span><br /> <p><b><span>Where is it located?</span></b><span> The location of this device depends on the design and age of engine.<span> </span>On many modern overhead cam shaft engines the cam shaft sensor is located either on the end, or to the side of the end, of the cam shaft housing.<span> </span>On older pushrod engines the cam sensor is found where the distributor would once have been located.<span> </span>This type sensor assembly makes use of the distributor shaft meshing directly, at its bottom end, with a gear on the cam within the engine block.<span> </span>In this respect the distributor shaft is just an extension of the cam shaft.<span> </span>On the top end of this distributor shaft is a magnetic armature.<span> </span>The cam shaft sensor, that measures the movement of this armature, is located in the cover and uses either magnetic or 'Hall effect' pickup modules.<span> </span></span><br /> <p><b><span> </span></b><br /> <p><b><span>How does it work?</span></b><span><span> </span>The sensor detects the position of a magnet or set of teeth on the gear on the end of the cam.<span> </span>An electrical waveform output signal is sent to the ECU as the cam turns.<span> </span>The cam sensor tells the ECU that cylinder 1 is at TDC on its compression stroke prior to ignition. <span> </span>The cam sensor ensures the correct timing of the fuel injection cycle.<span> </span>If the timing belt ever jumps a tooth on the cam the lack of agreement between the respective signals from the cam and crank sensors is indicated as an error condition by the ECU. </span><br /> <p><b><u><span><span> </span></span></u></b><br /> <p><b><u><span>Symptoms of faulty cam sensor</span></u></b><br /> <p><b><span>Associated OBD2 error codes DTCs: <span> </span>P0341 - P0349; P1345</span></b><br /> <p><b><span> </span></b><br /> <ul> <li><b><span>Hesitant acceleration - </span></b><span>miss-timing of fuel injection due to a faulty CMP can cause intermittent loss of power.<b></b></span></li> <li><b><span>Starting difficulty/failure.<span> </span></span></b><span>If the faulty CMP timing problems are severe they may cause the engine not fire at all, or to fire and then stall, or stall at some random time without warning.<b></b></span></li> <li><b><span>Hot engine stall and failure to restart - </span></b><span>Sometimes the fault of the CSS only manifests itself when the engine is hot.<span> </span>Over time thermal stress can cause cracking and can weaken electrical junctions within the CMP.<span> </span>The CMP may work well at cold start up but can then cause a hot running engine to stop with little chance of restart whilst the engine is still hot;<span> </span>once cooled the down the engine may readily restart and again run for a limited period until hot.</span></li></ul> <p><b><u><span>Note </span></u></b><span>The cam sensor body often protrudes into the cam shaft gallery and when it's 'o' ring seal<span> </span>becomes age hardened, engine oil may leak back into the sensor electrical socket plug connector causing errors due to interruption of signal. </span><br /> <p><b><span> </span></b><br /> <p><b><span>How to check? </span></b><span>It is not technically<b> </b>easy<b> </b>to determine that the CMP is at fault and, like the crank sensor, may require the use of an oscilloscope.<span> </span>If it is part of a sophisticated on board diagnostics system its failure may be logged as a specific error code in the ECU. Due to the variability problems with engine running are often experienced well before any error codes are set by the ECU.</span><br /> <p><span> </span><br /> <p><span><span> </span>2 pin socket (magnetic - sine wave output).<span> </span>One pin is 'ground' the other is 'signal'.<span> </span>A voltmeter set to 2 volts AC should measure a signal in the 0.2 to 2 volts range on the 'signal' pin.</span><br /> <p><span><span> </span>3 pin socket (Hall effect, magneto - square wave form output).<span> </span>One pin is 'reference' (5volts), one pin is 'ground' and the third pin is 'signal'.<span> </span>A DC voltage should be detectable in the 0.5 to 1.5 volt range from the 'signal' pin.</span><br /> <p><span>It is important that the voltage measurement take place at start up when the engine is cold and again, 20 minutes later, when the engine has fully warmed up to operating temperature. Often the voltage output from faulty sensors declines with temperature rise.</span><br /> <p><span> </span><br /> <p><b><span>How to fix?<span> </span></span></b><span>If the CMP failure is due oil leakage into the electrical connector then a thorough clean and a renewal of the oil seal on the CMP may correct the situation.<span> </span>It can be a wise precaution to change the connecting cable as oil migration beneath the insulation may possibly contaminate components at some distance to the CMP.<span> </span></span><br /> <p><span>If the CMP has an internal fault then it must be replaced.</span><br />

on Jul 22, 2011 | Mercedes-Benz E-Class Cars & Trucks

1 Answer

Where is the cam sensor in a 2002 nissan quest?


HI Chuck! The cam position sensor is inside the distributor on the quest. If the cam sensor has gone bad you need to replace the distributor assembly as it is not servicable. Before replacing the distributor, take the cap off and make sure the rotor is turning when you crank the engine. If it is not then check the timing belt as the distributor is driven by the cam shaft. If the belt is broken the cam shaft will not turn and you could get this code.The cam sensor is located under the plastic cover located under the rotor button

Nov 18, 2016 | Nissan Cars & Trucks

1 Answer

Where is my camshaft position sensor located on a 2008 chevy aveo


It should be located between the cam shafts. If you remove the Beauty Cover (( that's what they call the cover across the top of the motor. )) And then the Valve Cover. The Cam Sensor will be sitting between the Cam Shafts. Closer to the Intake Cam Shaft.

Aug 16, 2014 | Cars & Trucks

1 Answer

Where is the cam shaft sensor located in a 1996 jimmy 4.3litre engine


On V6 engines with a distributor, the sensor is inside the distributor.

Jun 10, 2013 | GMC Cars & Trucks

1 Answer

Timind belt diagram


i would say your looking at a faulty cam shaft sensor..its located on front side of engine. this fixed the same problem i had..there are 2 sensors one being your cam shaft sensor (normal to go out) and the crank shaft sensor..these work inline with computer to determine correct timing.hope this helps

Dec 07, 2011 | 2000 Ford Escort

1 Answer

How to find where the cam shaft sensor is located


The cam shaft position sensor is located right behind the exhost cam by the fire wall. It is held by two 10 mm bolts, one on each side of the sensor. If you got the hood up and looking at the engine the cam that is on the right hand is the exhost cam. To get to the CPS you have to remove the intake and cam top cover.

Jun 13, 2009 | 1999 Kia Sportage

1 Answer

Cam shaft sensor


It should be at the rear of the head at the end of the camshaft. some are located at the front of the head. Either one, there is a 2 prong plug that goes to it.

Jun 11, 2008 | 2001 Mazda 626

Not finding what you are looking for?
2004 Suzuki Forenza Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...